Programmers / JTAG
JTAG programmers, adapters and devices for communication with mobile phones. UFS / eMMC device programmer designed to read / write and repair data using both the ISP and Direct method. Communication takes place in various JTAG, SD or MPHY protocols. VR-TABLE enables communication, reading and writing of memory via EMMS, JTAG or communication in FBUS mode.
22089 |
Moorc E-Mate X 13in1 - ICFriend Edition Moorc E-Mate X 13in1 - ICFriend Edition is the latest version of a set of adapters allowing for direct eMMC memory connection and read and/or write it contest. Adapter/Socket is fully compatible with many eMMC devices, such as Riff Box, Riff Box 2, Medusa Pro Box, Z3X Easy Jtag Box, Easy Z3x Plus, GPG EMMC Box, UFi Box, etc. The new version in comparison to the 2017 edition allows in addition to previously supported pinouts also reading the latest eMMCs BGA254, BGA100, BGA136, BGA168. |
70 |
Pony programmer cable for 24xxx chips - very cheap, fast and 100% working eeprom reader ! |
21681 |
SD-EMMC Plus Adapter - Model SE-P1 SD-EMMC Plus Adapter - Model SE-P1 is the latest adapter to connect eMMC memory using ISP or after Chip-Off by ordinary SD card reader or MMC Plus card reader (8-bit transmission). In addition, the adapter has a possibility to choose whether the power to eMMC (VCC and VCCq) is taken from the reader, ie. 3.3V or from an external power source Lab power supply (VccQ and Vcc) |
22317 |
SPI adapter for Z3x and UFI Box SPI adapter for Z3x and UFI Box makes it possible to create a sector copy/read NOR memory (SOIC8 / WSON8) found in low-budget phones (eg Nokia 230, Nokia 105 etc.). using the Z3x Box or UFI Box |
22162 |
Test Module 1 for JC PRO 1000S - Battery Tester Test Module 1 for JC PRO 1000S - Battery Tester allows you to test the batteries available on the iPhone in terms of originality, degree of wear, working time, i.e. charging cycles. |
22163 |
Test Module 2 for JC PRO 1000S - Lightning Apple Cable Tester Test Module 2 for JC PRO 1000S - Lightning Apple Cable Tester allows you to test Lightning cables for their proper operation (data transmission / loading) as well as check their authenticity (correctness of the MFI certificate) |
22765 |
UFi Box + UFi UFS-Prog - Worldwide version UFi Box + UFi UFS-Prog - Worldwide version is the most advanced box for eMMC / eMMCP / UFS in Direct / ISP mode. Thanks to the very simple interface, you can repair eMMC devices much simpler that before (resize partition, format, smart test, read and write) and also repair your phones with ADB (HSQUSB 9008) and SPI software (NOR readings). |
22569 |
UFI-Lite USB3.0 SuperSpeed uSD/eMMC Reader for UFI-Box UFI-Lite USB3.0 SuperSpeed uSD/eMMC Reader for UFI-Box this reader is intended for UFI-Box. UFI-Box is a powerful EMMC Service Tool for Samsung, China phone SK Hynix, Toshiba, Kingston, Micron, and other brands. |
22310 |
UFS BGA95 adapter for Easy Z3x Plus UFS BGA95 adapter for Easy Z3x Plus enables the UFS IC BGA 095 readings via Easy Z3x Plus. The adapter, unlike the current DediProg device (Nuprog E), also supports Toshiba chips and does not require reballing the IC before reading it. |
22780 |
Universal engineering programmer NuProg-E2 (eMMC, UFS, NAND, NOR) Universal engineering programmer NuProg-E2 (eMMC, UFS, NAND, NOR) widely supports most IC types on the market, UFS, eMMC, MCU, CPLD, FPGA, SPI NOR, SPI NAND, Parallel NOR, Parallel NAND and EEPROM, etc. And also support different types of IC packages: CSP, BGA, QFN, QFP, SOP, TSOP, SSOP, PLCC, DIP, etc. Designed FPGA kernel architecture supplies ultra high speed programming performance. The Programming project and sockets are compatible with NuProgPlus. Together with built-in SuperSpeed® USB 3.0 for high-speed communication, it is an efficient tool for you to focus on application analysis and product development. |
21225 |
Universal JTAG/eMMC/FBUS JE-02 adapter Universal JTAG/eMMC/FBUS JE-02 adapter it's fully configurable universal adapter that allows you fully configure connection for diffrent JTAG/eMMC devices (Medusa PRO, Riff Box, GPG eMMC,. ORT) but also those which use Rj45/RJ48 for communication (ATF Nitro, ATF Gold, Medusa, OctoPlus). Adapter helps you in connection to target if you wish to solder to your phone/modem PCB using wires but want to configure it for your needs.. On adapter you will find all signals used in Riff Box JTAG |
1529 |
Xilinx JTAG Programmer enables you to programm/verify/read/secure/test Xilinx CPLD and FPGA devices in a operating voltage range from 3 to 5 Volts in-circuit. It`s a buffered Interface containing logic to protect your PC's parallel port and your target system. The pinout is compatible to UFS devices. Reference Data Free programming software (Xilinx Impact) for the Xilinx JTAG Programmer: http://www.xilinx.com |
22467 |
Z3X Easy-Jtag Plus BGA-254 2-in-1 eMMC/UFS Socket Adapter Z3X Easy-Jtag Plus BGA-254 2-in-1 eMMC/UFS + ISP Socket Adapter is designed for Z3X Easy-Jtag Plus devices. It enables reading and writing parameters via Direct Mode as also ISP due output signal on adapter. It is characterized by high quality and high positioning accuracy. ECDSA Protected Serial Number (protected from illegal copying). |
22867 |
Moorc ICFRIEND EASY JTAG UFS 4in1 + EMMC ISP S1 adapters Moorc ICFRIEND EASY JTAG UFS 4in1 + EMMC ISP S1 adapters - the adapter allows you to make a direct connection of eMMC memory and perform reading and/or writing. EASY BOX and EMMC compatible adapter. It has the ability to solder the U2 encryption system - the adapter is without a system. |
22630 |
MOORC MIPITESTER/MiPi Box Pro Programmer for EMMC and UFS MOORC MIPITESTER/MiPi Box Pro Programmer for EMMC and UFS is a UFS / eMMC device programmer designed to read / write and repair data using both the ISP and Direct method. The set includes UFS (297/254/153) and eMMC / eMCP (153-169, 254, 221, 162-186, 100, 136, 529, 168) adapters. |
22326 |
Easy Jtag Z3X Plus Ultimate 16in1 (JTAG/eMMC/UFS) Easy Jtag Z3X Plus Ultimate 16in1 (JTAG/eMMC/UFS) is a complete device for communication via JTAG, SD (read/write eMMC / eMCP) and MPHY protocol (read/write UFS). The Ultimate version consists of the Easy Z3x Plus interface with a set of 13in1 adapters for reading 99% of eMMC / eMCP systems together with 3in1 adapters for reading UFS (BGA 153, 95 and 254). The interface of the well-known Z3x group - of which Multi-COM is the official representative - not only serves to repair the bootloader but has a built-in PinFinder so that we can find the JTAG pinout in a few seconds. The box also supports the latest version of the full 4-bit ISP transmission and MPHY protocol (read / write UFS memory). In addition, the Box has a fully functional Fbus and SPI communication module, thanks to which it will be possible to flash a repaired phone without additional devices. |
17203 |
GPG EMMC JTAG Box Full + 33 JIG GPG EMMC JTAG Box Full + 33 JIG is a box for repairing dead Android and WP8 phones with EMMC. The supported model range includes Samsung I9300/I9100, HTC G14, Sony, China ZTE/China Huawei/China MTK and thousands of other phones and brands. GPG EMMC support does not depend on the phone model. You can fulfill Read / Write operations with any phones that have a supported EMMC IC. |
14305 |
GPG EMMC JTAG Box is a box for repairing dead Android and WP8 phones with EMMC. The supported model range includes Samsung I9300/I9100, HTC G14, Sony, China ZTE/China Huawei/China MTK and thousands of other phones and brands. GPG EMMC support does not depend on the phone model. You can fulfill Read / Write operations with any phones that have a supported EMMC IC. |
16059 |
Universal adapter for JTAG Box Universal adapter for JTAG Box helps you in connection to target if you wish to solder to your phone/modem PCB using wires. On adapter you will find all signals used in Riff Box JTAG |
7883 |
RIFF Box JTAG/EMMC ORIGINAL it's new device from Rocker Team is finally released on market - now also support EMMC/Direct. There is no other device with so many complex functions supported. As always, Rocker team are presenting something unique and wonderful. It will suit most of regular user needs, although is aimed at advanced developers who need to debug their own embedded code. Unique scripting support, GDB Server for IDA real time debugging, Trace32 scripts compatibility and high quality hardware will be on Your service. Our R&D Team is ready to serve our valued customers as well as our tech support staff. |