EMMC adapters and cables used in interfaces and boxex
EMMC adapters and cables support the communication process between devices and EMMC memories. They enable direct or indirect connection of eMMC memory and execution of reading and writing. Adapters are used to program eMMC memory chips in phones without soldering - which definitely affects the recovery process.
16973 |
Adapter for ATF 20PIN EMMC - RJ45 Adapter for ATF 20PIN EMMC - RJ45 is used to allow connection EMMC Adapter with 20 pin connector to ATF Box. |
15020 |
Adapter GPG-FT232 dla GPG eMMC Box Adapter GPG-FT232 dla GPG eMMC Box is to solve all of connectivity ISP issue such as: eMMC ORC: 00000000, bad code ! >> Id check lost. |
17319 |
Adapter EMMC for Riff BOX (RC1000) Adapter EMMC for Riff BOX - RC1000 allows a very simple repair phones with blocked JTAG access (GT-i9300 / N7100 / N719 / N7102, etc.), repair phones with damaged JTAG points/pads (access to ROM2 by EMMC) or read/write EMMC applicable for the data recovery/analysis. Using the adapter you can perform format EMMC or low-format (in case of damage EMMC), CMD42 Lock/Unlock/Pasword reset or Samsung eMMC Factory Format. Our adapter allows you to connect in ISP mode (directly onto your phone without removing the EMMC) or Direct (by removing the BGA soldering and the corresponding memory fields or using adapter). |
21191 |
Adapter EMMC/JTAG ATF v2 5in1 GPG Adapter EMMC/JTAG ATF v2 5in1 GPG is leatest edition of GPG adapter for ATF users that allows you to use special JTAG / EMMC / ISP functions with your ATF Box. |
22366 |
Adapter eMMC/JTAG dla Riff Box 2 - RC3000 Adapter eMMC/JTAG dla Riff Box 2 - RC3000 is an additional adapter for Riff BOX that allows you to solve problems with ISP communication. From now on it is not necessary to desolder the resistor on the CLK bus. Of course, it also allows operation of phones with damaged JTAG points (access to ROM2 via EMMC) or write / read EMMC (applicable for data recovery using the new IDC30 pin connector). Thanks to it you can do EMMC format or low-format in case of EMMC damage, repartitions (Slave / Master) or EMMC cloning. It also allows connection in ISP mode (directly into the phone's board without removing the EMMC chip) and Direct (by removing the BGA chip and soldering to the appropriate memory fields or using an adapter). We connect via JTAG and IDC20 socket. |
21231 |
Adapter eMMC/JTAG for Riff BOX 2 - RC2000 Adapter eMMC/JTAG for Riff BOX 2 - RC2000 allows a very simple repair phones by JTAG using IDC20 pin connector known from previous riff but offers also support for eMMC using leatest 30 pin connector (IDC 30 pin). By this you can repair phones with blocked JTAG access (GT-i9300 / N7100 / N719 / N7102, etc.), repair phones with damaged JTAG points/pads (access to ROM2 by EMMC) or read/write EMMC applicable for the data recovery/analysis. Using the adapter you can perform format EMMC or low-format (in case of damage EMMC), CMD42 Lock/Unlock/Pasword reset or Samsung eMMC Factory Format. Our adapter allows you to connect in ISP mode (directly onto your phone without removing the EMMC) or Direct (by removing the BGA soldering and the corresponding memory fields or using adapter). |
22626 |
Easy Z3X Plus converter to the SE-P1 adapter Easy Z3X Plus converter to the SE-P1 adapter allows you to use the soldered adapter supplied with the Easy Z3x Plus box in order to connect it with the SE-P1 adapter and the SD card reader. The solution is useful when performing images and tests with the use of other software for SD eMMC ISP without the need to desolder the already made connection. |
13278 |
EMMC adapter for Easy Z3x JTAG Box EMMC adapter for Easy Z3x JTAG Box allows to easy repair of phones with disabled access to bootloader via DCC (GT-i9300/N7100/N719/N7102) or phones with demaged JTAG pinouts (access to ROM2 by EMMC). Adapter allows also in PRO version for low level formating of EMMC, easy one button repair boot via EMMC Direct, repartition Slave/Master. Our adapter you can use for ISP (in phone board) and direct connection. |
21854 |
EMMC NAND Adapter -> LA allows trouble-free eMMC connectivity through the built-in controller as well as all NAND bus interfaces for analysis via Logic Analyzer. Adapter mainly used for finding NAND pinouts for eMMC chips with faulty controller. |
21713 |
Frames / Limiters adapters for BGA (spacer) Frames / Limiters adapters for BGA (spacer) is a replacement frame for readers / adapters of BGA eMMC company Antech Electronics for mounting different sizes of BGA chips without having to replace the adapter. In our offer you will find all possible frame sizes of 10x11mm, through 11,5x13mm as well as less standard frame 15x15mm or 14x18mm |
23153 |
ICFriend UFS Socket 3in1 set (297/153/254) for Z3X Easy Jtag Plus ICFriend UFS Socket 3in1 set for Z3X Easy Jtag Plus will enable the user to work with newer UFS chipsets, and let you read data / write data etc. ICFriend Supports: UFS BGA153 Chip, UFS EMMC BGA254 Chip and UFS BGA297 Chip. |
23152 |
ICFriend UFS Socket 6w1 set for Z3X Easy Jtag Plus ICFriend UFS Socket 6w1 set for Z3X Easy Jtag Plus will enable the user to work with newer UFS chipsets, and let you read data / write data etc. ICFriend Supports: UFS BGA153 Chip, UFS EMMC BGA254 Chip and UFS BGA297 Chip. |
21775 |
JTAG/eMMC ISP 4in1 Adapter Kit MOORC 2018 JTAG/eMMC ISP 4in1 Adapter Kit MOORC 2018 is a set of adapters that offer direct programming (BGA162 / 186, BGA 153/169 and BGA 221) with Riff, Easy Z3x JTAG, ORT, GPG as well as use JTAG communication. |
22939 |
Medusa Pro II UFS BGA-153 Socket Medusa Pro II UFS BGA-153 Socket is intended for Medusa Pro II Box. |
22089 |
Moorc E-Mate X 13in1 - ICFriend Edition Moorc E-Mate X 13in1 - ICFriend Edition is the latest version of a set of adapters allowing for direct eMMC memory connection and read and/or write it contest. Adapter/Socket is fully compatible with many eMMC devices, such as Riff Box, Riff Box 2, Medusa Pro Box, Z3X Easy Jtag Box, Easy Z3x Plus, GPG EMMC Box, UFi Box, etc. The new version in comparison to the 2017 edition allows in addition to previously supported pinouts also reading the latest eMMCs BGA254, BGA100, BGA136, BGA168. |
21681 |
SD-EMMC Plus Adapter - Model SE-P1 SD-EMMC Plus Adapter - Model SE-P1 is the latest adapter to connect eMMC memory using ISP or after Chip-Off by ordinary SD card reader or MMC Plus card reader (8-bit transmission). In addition, the adapter has a possibility to choose whether the power to eMMC (VCC and VCCq) is taken from the reader, ie. 3.3V or from an external power source Lab power supply (VccQ and Vcc) |
22743 |
SD/MicroSD reader for a Z3x JTAG Plus - 1bit SD/MicroSD reader for a Z3x JTAG Plus - 1bit allows you to read SD and MicroSD cards via Z3x Box Plus. By using the option of skipping bad sectors and selecting a voltage other than the standard 3.3V by the Z3x Box Plus, it is possible to physically dump problematic memories that the standard SD / MicroSD card reader cannot copy. The reader works in 1 bit mode and is compatible with the Z3X ISP pinout. |
22569 |
UFI-Lite USB3.0 SuperSpeed uSD/eMMC Reader for UFI-Box UFI-Lite USB3.0 SuperSpeed uSD/eMMC Reader for UFI-Box this reader is intended for UFI-Box. UFI-Box is a powerful EMMC Service Tool for Samsung, China phone SK Hynix, Toshiba, Kingston, Micron, and other brands. |
21225 |
Universal JTAG/eMMC/FBUS JE-02 adapter Universal JTAG/eMMC/FBUS JE-02 adapter it's fully configurable universal adapter that allows you fully configure connection for diffrent JTAG/eMMC devices (Medusa PRO, Riff Box, GPG eMMC,. ORT) but also those which use Rj45/RJ48 for communication (ATF Nitro, ATF Gold, Medusa, OctoPlus). Adapter helps you in connection to target if you wish to solder to your phone/modem PCB using wires but want to configure it for your needs.. On adapter you will find all signals used in Riff Box JTAG |
17327 |
VR-TABLE for JTAG EMMC FBUS Tool VR-TABLE for JTAG/EMMC/FBUS Tool is a precision tool for non-invasive ISP (ie, In System Programming) Reading and writing via EMMC, JTAG which replaces the need for soldering or desoldering anything in motherboard. VRTable enables forensic examiners to acquire data from Mobile Devices, GPS Devices and other electronics units. Optimization is based on a fully individually configurable VR-ARMS ended precision probes and additional reference voltages for all types of memory. VRTable can be also freely used in the car diagnostics (car radios, controllers) as well as in FBUS communication mode - completely replacing the RJ45/RJ48 cables. |