|
Main page > Repair Equipment > Repair of displays (LCD) > Laminators for Polarizer/OCA > Laminator GM928 with forms for Samsung
|
 |
Laminator GM928 with forms for Samsung
LCD and OCA laminator with forms for Samsung is used to connect curved displays with a new glass of Samsung S6 EDGE, S6 EDGE +, S7 EDGE, S8, S8 +, S9, S9 +, NOTE8 and flat displays as well as applying OCA slices on a new curved glass. The entire joining process consists in pressing the two elements together with a heated pressure press using a pressure of 3-5kg / cm2 in a vacuum. The attached forms for these Samsung phone models are used for this purpose.
Forms* for curved screens:
- Samsung S6 EDGE,
- Samsung S6 EDGE +,
- Samsung S7 EDGE,
- Samsung S8, S8 +,
- Samsung S9,
- Samsung S9 +,
- Samsung NOTE 8,
* intended for applying OCA adhesive on the display (replaces the OCA laminator) and for laminating curved screens in the laminator with simultaneous pressing of the corners. The device has a flat bottom and top surface of lamination so you can also combine all flat displays!
Specification:
- counter of laminations made,
- operating status of all solenoid valves visualized on the display,
- pressure gauges indicating LCD and OCA lamination pressure as well as vacuum values,
- S8, S8 +, S9, S9 + rubber molds have grooved holes for flex tapes - no need to bend them in the lamination process (in the pictures below - sample set for Samsung Galaxy S9).
When using GM-928, there is no need to have a separate laminator for applying OCA patches to the glass, because the GM-928 does it alone in one of the stages of the LCD screen repair process. If as a result of this process small air bubbles remain, use an autoclave available on our other auctions.
The laminator needs additionally:
- vacuum pump (manufacturer recommends target pressure -94 .. -98kPa)
- a compressor with a working pressure of 0.4-0.6 MPa (4-6 bar)
The vacuum pump and compressor are NOT INCLUDED! After connecting these two elements and setting the parameters of the laminator, it is ready for operation.
The device is very different from other similar designs on the market because for each of two lamination processes, i.e:
- connecting a curved or flat display with a new glass
- applying OCA patches to the new curved glass.
you can set separate the following parameters:
- pressure on the LCD during the lamination of the glass with the display,
- the force of pressure on the glass during lamination of the OCA adhesive with a new glass,
- lamination temperature,
- lamination time,
- operating time of the vacuum pump. / li>
Small dimensions and great capabilities of the GM928 device put it in the forefront of devices for comprehensive repairs of phone screens.
Parameters:
- power supply voltage: 220-240VAC
- power: 800W
- regulation with press force: yes 0-10 kg / cm2 (for both modes)
- information about the pressure force: yes in kg / cm2
- temperature regulation: 0-80C
- required air pressure: 0.4-0.6MPa (4-6 bar)
- required underpressure: -94 ... -98kPa
- height of the laminar chamber: 7.5 cm (for flat displays)
- width of the laminar chamber: 17cm (for flat displays)
- depth of the laminar chamber: 18cm (for flat displays)
- external dimensions: 23 [szer] x37 [depth] x41 [height] cm
- net weight: 18kg
Kit contents:
- vacuum-pressure laminator GM928
- OCA and LCD lamination kit for S6 EDGE, S6 EDGE +, S7 EDGE, S8, S8 +, S9, S9 +, NOTE8
- user manual
- polyurethane foam 160x190x6mm
Forms* for curved screens:
- Samsung S6 EDGE,
- Samsung S6 EDGE +,
- Samsung S7 EDGE,
- Samsung S8, S8 +,
- Samsung S9,
- Samsung S9 +,
- Samsung NOTE 8,
* intended for applying OCA adhesive on the display (replaces the OCA laminator) and for laminating curved screens in the laminator with simultaneous pressing of the corners. The device has a flat bottom and top surface of lamination so you can also combine all flat displays!
Specification:
- counter of laminations made,
- operating status of all solenoid valves visualized on the display,
- pressure gauges indicating LCD and OCA lamination pressure as well as vacuum values,
- S8, S8 +, S9, S9 + rubber molds have grooved holes for flex tapes - no need to bend them in the lamination process (in the pictures below - sample set for Samsung Galaxy S9).
When using GM-928, there is no need to have a separate laminator for applying OCA patches to the glass, because the GM-928 does it alone in one of the stages of the LCD screen repair process. If as a result of this process small air bubbles remain, use an autoclave available on our other auctions.
The laminator needs additionally:
- vacuum pump (manufacturer recommends target pressure -94 .. -98kPa)
- a compressor with a working pressure of 0.4-0.6 MPa (4-6 bar)
The vacuum pump and compressor are NOT INCLUDED! After connecting these two elements and setting the parameters of the laminator, it is ready for operation.
The device is very different from other similar designs on the market because for each of two lamination processes, i.e:
- connecting a curved or flat display with a new glass
- applying OCA patches to the new curved glass.
you can set separate the following parameters:
- pressure on the LCD during the lamination of the glass with the display,
- the force of pressure on the glass during lamination of the OCA adhesive with a new glass,
- lamination temperature,
- lamination time,
- operating time of the vacuum pump. / li>
Small dimensions and great capabilities of the GM928 device put it in the forefront of devices for comprehensive repairs of phone screens.
Parameters:
- power supply voltage: 220-240VAC
- power: 800W
- regulation with press force: yes 0-10 kg / cm2 (for both modes)
- information about the pressure force: yes in kg / cm2
- temperature regulation: 0-80C
- required air pressure: 0.4-0.6MPa (4-6 bar)
- required underpressure: -94 ... -98kPa
- height of the laminar chamber: 7.5 cm (for flat displays)
- width of the laminar chamber: 17cm (for flat displays)
- depth of the laminar chamber: 18cm (for flat displays)
- external dimensions: 23 [szer] x37 [depth] x41 [height] cm
- net weight: 18kg
Kit contents:
- vacuum-pressure laminator GM928
- OCA and LCD lamination kit for S6 EDGE, S6 EDGE +, S7 EDGE, S8, S8 +, S9, S9 +, NOTE8
- user manual
- polyurethane foam 160x190x6mm
|
||
NEGOTIATE PRICE
If you are interested in
Laminator GM928 with forms for Samsung
you will probably want to take a look at following products:
You might also be interested in:
+
|
Automatic vacuum laminator TBK763 OCA 7'' (Compressed Air version)
more
|
Price:
299.00 EUR w/o VAT |
+
|
REMAX Screen Attach Machine for tablets
more
|
Price:
18.00 EUR w/o VAT |
+
|
HONGZHUN JIDIAN FM-02 laminator 2in1
more
|
Price:
409.00 EUR w/o VAT |
+
|
Automatic vacuum laminator TBK K-765 7,4"
more
|
Price:
309.00 EUR w/o VAT |
+
|
UYUE X13S laminator LCD/OCA for straight and curved screens 15.1" (24x30cm)
more
|
Price:
969.00 EUR w/o VAT |
+
|
Vaccum OCA laminator Type 2
more
|
Price:
149.00 EUR w/o VAT |
+
|
Automatic vacuum laminator OCA TBK K-786 Edge
more
|
Price:
499.00 EUR w/o VAT |
+
|
Vaccum OCA laminator TBK 761 with build-in pump
more
|
Price:
269.00 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.
