Cables and Adapters for fast reading using EMMC devices
17319 |
Adapter EMMC for Riff BOX (RC1000) Adapter EMMC for Riff BOX - RC1000 allows a very simple repair phones with blocked JTAG access (GT-i9300 / N7100 / N719 / N7102, etc.), repair phones with damaged JTAG points/pads (access to ROM2 by EMMC) or read/write EMMC applicable for the data recovery/analysis. Using the adapter you can perform format EMMC or low-format (in case of damage EMMC), CMD42 Lock/Unlock/Pasword reset or Samsung eMMC Factory Format. Our adapter allows you to connect in ISP mode (directly onto your phone without removing the EMMC) or Direct (by removing the BGA soldering and the corresponding memory fields or using adapter). |
21191 |
Adapter EMMC/JTAG ATF v2 5in1 GPG Adapter EMMC/JTAG ATF v2 5in1 GPG is leatest edition of GPG adapter for ATF users that allows you to use special JTAG / EMMC / ISP functions with your ATF Box. |
22366 |
Adapter eMMC/JTAG dla Riff Box 2 - RC3000 Adapter eMMC/JTAG dla Riff Box 2 - RC3000 is an additional adapter for Riff BOX that allows you to solve problems with ISP communication. From now on it is not necessary to desolder the resistor on the CLK bus. Of course, it also allows operation of phones with damaged JTAG points (access to ROM2 via EMMC) or write / read EMMC (applicable for data recovery using the new IDC30 pin connector). Thanks to it you can do EMMC format or low-format in case of EMMC damage, repartitions (Slave / Master) or EMMC cloning. It also allows connection in ISP mode (directly into the phone's board without removing the EMMC chip) and Direct (by removing the BGA chip and soldering to the appropriate memory fields or using an adapter). We connect via JTAG and IDC20 socket. |
21231 |
Adapter eMMC/JTAG for Riff BOX 2 - RC2000 Adapter eMMC/JTAG for Riff BOX 2 - RC2000 allows a very simple repair phones by JTAG using IDC20 pin connector known from previous riff but offers also support for eMMC using leatest 30 pin connector (IDC 30 pin). By this you can repair phones with blocked JTAG access (GT-i9300 / N7100 / N719 / N7102, etc.), repair phones with damaged JTAG points/pads (access to ROM2 by EMMC) or read/write EMMC applicable for the data recovery/analysis. Using the adapter you can perform format EMMC or low-format (in case of damage EMMC), CMD42 Lock/Unlock/Pasword reset or Samsung eMMC Factory Format. Our adapter allows you to connect in ISP mode (directly onto your phone without removing the EMMC) or Direct (by removing the BGA soldering and the corresponding memory fields or using adapter). |
16973 |
Adapter for ATF 20PIN EMMC - RJ45 Adapter for ATF 20PIN EMMC - RJ45 is used to allow connection EMMC Adapter with 20 pin connector to ATF Box. |
15020 |
Adapter GPG-FT232 dla GPG eMMC Box Adapter GPG-FT232 dla GPG eMMC Box is to solve all of connectivity ISP issue such as: eMMC ORC: 00000000, bad code ! >> Id check lost. |
13278 |
EMMC adapter for Easy Z3x JTAG Box EMMC adapter for Easy Z3x JTAG Box allows to easy repair of phones with disabled access to bootloader via DCC (GT-i9300/N7100/N719/N7102) or phones with demaged JTAG pinouts (access to ROM2 by EMMC). Adapter allows also in PRO version for low level formating of EMMC, easy one button repair boot via EMMC Direct, repartition Slave/Master. Our adapter you can use for ISP (in phone board) and direct connection. |
22726 |
eMMC/UFS ICFriend AndroidKing Adapter Set 9in1 + AK5 eMMC/UFS ICFriend AndroidKing Adapter Set 9in1 + AK5 is a set of eMMC / UFS adapters for reading eMMC and UFS bones along with AK5 (Easy JTAG Plus) adapter . The set allows to read nearly 90% of BGA chips available on the market, such as eMMC / eMCP BGA 153, 169, 162, 221, 254, 186 as well as UFS BGA 153, 254, 95 chips |
22881 |
ISP S2 adapter for MiPi Tester UFS/eMMC ISP S2 adapter for MiPi Tester UFS/eMMC allows you to service any device with ISP pinouts via UFS/eMMC interface. Intended for MiPi Box. |
17312 |
Jumper wire/Copper spool wire 0.10mm/50m Jumper wire/Copper spool wire 0.10mm/50m is a thin (0.10mm) insulated wire to make precise connections - are ideal for connecting corroded tracks in phones and other repair work. Thanks to its thick it also successfully used for soldering JTAG and when reading dump by EMMC |
22089 |
Moorc E-Mate X 13in1 - ICFriend Edition Moorc E-Mate X 13in1 - ICFriend Edition is the latest version of a set of adapters allowing for direct eMMC memory connection and read and/or write it contest. Adapter/Socket is fully compatible with many eMMC devices, such as Riff Box, Riff Box 2, Medusa Pro Box, Z3X Easy Jtag Box, Easy Z3x Plus, GPG EMMC Box, UFi Box, etc. The new version in comparison to the 2017 edition allows in addition to previously supported pinouts also reading the latest eMMCs BGA254, BGA100, BGA136, BGA168. |
21209 |
Multicolored M-M cables 17 cm to the contact plate - 40 pcs Multicolored M-M cables 17 cm to the contact plate - 40 pcs is a set of different colored wires connecting M-M ideally suited for making connections between the contact plates and sets of commissioning. Wires can be easily separated from each other - great to use with JTAG/eMMC connections. |
21681 |
SD-EMMC Plus Adapter - Model SE-P1 SD-EMMC Plus Adapter - Model SE-P1 is the latest adapter to connect eMMC memory using ISP or after Chip-Off by ordinary SD card reader or MMC Plus card reader (8-bit transmission). In addition, the adapter has a possibility to choose whether the power to eMMC (VCC and VCCq) is taken from the reader, ie. 3.3V or from an external power source Lab power supply (VccQ and Vcc) |
22743 |
SD/MicroSD reader for a Z3x JTAG Plus - 1bit SD/MicroSD reader for a Z3x JTAG Plus - 1bit allows you to read SD and MicroSD cards via Z3x Box Plus. By using the option of skipping bad sectors and selecting a voltage other than the standard 3.3V by the Z3x Box Plus, it is possible to physically dump problematic memories that the standard SD / MicroSD card reader cannot copy. The reader works in 1 bit mode and is compatible with the Z3X ISP pinout. |
21210 |
Set 140 pcs. Of wires to the contact plate WJW-70 Set 140 pcs. Of wires to the contact plate WJW-70B kit includes jumper connecting different length and color, to be joined on the fields included in our ofercie.płytkach contact. Content of 140 different colored jumper lengths of 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, 125mm. The whole is packaged in a box aesthetic. |
21208 |
Set of 40 pcs. M-F cables in various colors with a length of 17 cm Set of 40 pcs. M-F cables in various colors with a length of 17 cm is a set of different colored wires connecting M-F ideally suited for making connections between the contact plates and sets of commissioning. Wires can be easily separated from each other - great to use with JTAG/eMMC connections. |
21225 |
Universal JTAG/eMMC/FBUS JE-02 adapter Universal JTAG/eMMC/FBUS JE-02 adapter it's fully configurable universal adapter that allows you fully configure connection for diffrent JTAG/eMMC devices (Medusa PRO, Riff Box, GPG eMMC,. ORT) but also those which use Rj45/RJ48 for communication (ATF Nitro, ATF Gold, Medusa, OctoPlus). Adapter helps you in connection to target if you wish to solder to your phone/modem PCB using wires but want to configure it for your needs.. On adapter you will find all signals used in Riff Box JTAG |
21620 |
Adapter Riff 2 Emate Pro USocket Adapter Riff 2 Emate Pro USocket it's additional adapter for eMate Moorc PRO v1 edition which allows to use universal BGA socket and connect it to Riff 2 box for eMMC reading. |
21886 |
E-Mate Pro eMMC Tool MoorC v3 - 2017 is the latest version of the MoorC adapter for all eMMC direct connection which allows read and write interface. The adapter is compatible with many emmc devices, such as Riff Box, Riff Box 2, Medusa Pro Box, Z3X Easy Jtag Box, GPG EMMC Box, UFi Box etc. New additionally equipped with short-circuit protection, additional adapter for 10x11mm systems, data and commnd pullups (Data / CMD) and improved support for UFI BOX |
22022 |
E-Tool eMMC 5in1 Reader/Adapter E-Tool eMMC 5in1 Reader/Adapter is needed to read / write eMMC chips using your professional eMMC tool, it allows you to perform direct chip reading and writing of eMMC chips. Compatible with many emmc tools including Riff Box 2, Medusa Pro Box, Z3X Easy Jtag Box, GPG EMMC Box, UFi Box etc. |