 |
Adapters and converters are intermediary accessories between a phone and a computer or a service device (box). They allow you to repair phones and communicate with the phone by putting them in the appropriate service modes, they allow you to find the pins to the EMMC. But they also have basic functions and enable communication and data transfer / transfer.
Adapter EMMC ATF V2 4in1
Adapter EMMC ATF V2 4in1 is adapter allows you to use special functions with your ATF Box, ATF Lightning or ATF Nitro. Thes features include: JTAG / EMMC / ISP / MMC CARD.
Functions:
1. JTAG Via Molex
You can use the JTAG function of your ATF Box and this ATF Adapter to unlock Lumia 610 and 510 via easier JTAG molex port.
Connect an FPC ribbon to your adapter, then connect the 610/510 connector to the ribbon and ultimately to the board of the phone via molex port.
2. EMMC Direct
You can use the BGA PCBS to direct Read / Write Emmc using this adapter with ATF JTAG PLUS software
3. MMC Card
You can use this Adapter to brute force MMC Cards and create special MMC Cards
4. JTAG / ISP / EMMC Direct Soldering
You can use this Adapter and solder wires direct to phone PCD for JTAG Repair aswell as ISP and EMMC Direct RepaIR.
Technical Improvements of ATF-V2 Version
The Switch
ON = Strong PULL-UP Resistors will be applied to eMMC CMD (BLUE) and DATA (GREEN) Lines.
---> This is very usefull for phones that require VccQ and Vcc Power Connections (Samsung, HTC etc)
OFF = PULL-UP Resistors WILL NOT be used.
---> This is normally done with Nokia Lumia Phones which does not require VccQ and Vcc Connections
For a more stable connection, set switch to "ON" and make sure to connect required power to VccQ and Vcc Lines
Voltage Jumper For Micro SD Cards
3.3v = Most New/Old Micro SD Cards are Compatible with 3.3v Vcc
1.8V = We have prepared a 1.8v Vcc for Future Low-Powered Micro SD Cards
EMMC Jumper
[For eMMC Use Only]
NC = Secondary CLOCK will not be used for eMMC Communication
CLK2 = Secondary CLOCK will be used for eMMC Communication
When adapter is used for a NON-EMMC Connection such as JTAG or Micro SD Card, make sure this DIP Switch is on the "NC" Position.
CLK2 is NOT REQUIRED for most eMMC Chips, but setting DIP SWITCH to CLK2 will give you a stronger CLK (RED) Signal for better eMMC Communication.
Nokia disassembly tool included
Compatibility:
- ATF Nitro
- ATF Box (Big Metal Box)
- ATF Lightning
Set contains
1 X Official ATF Version 2 All in 1 Adapter for ATF Box
1 X Set of Coloured JTAG Wires
3 X FPC Ribbon Cables
1 X Lumia 510 / 610 Connector
1 X Molex port for Lumia 610/510 (needed because some 610 / 510 do not have molex already onboard)
2 X BGA PCB
1 X Nokia mini opening tool kit containing:
1 X Leaver / Opener for Nokia disassembly
1 X Screwdriver for Nokia disassembly
2 X Plastic opening picks for Nokia disassembly
1 X Suction cup
Functions:
1. JTAG Via Molex
You can use the JTAG function of your ATF Box and this ATF Adapter to unlock Lumia 610 and 510 via easier JTAG molex port.
Connect an FPC ribbon to your adapter, then connect the 610/510 connector to the ribbon and ultimately to the board of the phone via molex port.
2. EMMC Direct
You can use the BGA PCBS to direct Read / Write Emmc using this adapter with ATF JTAG PLUS software
3. MMC Card
You can use this Adapter to brute force MMC Cards and create special MMC Cards
4. JTAG / ISP / EMMC Direct Soldering
You can use this Adapter and solder wires direct to phone PCD for JTAG Repair aswell as ISP and EMMC Direct RepaIR.
Technical Improvements of ATF-V2 Version
ON = Strong PULL-UP Resistors will be applied to eMMC CMD (BLUE) and DATA (GREEN) Lines.
---> This is very usefull for phones that require VccQ and Vcc Power Connections (Samsung, HTC etc)
OFF = PULL-UP Resistors WILL NOT be used.
---> This is normally done with Nokia Lumia Phones which does not require VccQ and Vcc Connections
For a more stable connection, set switch to "ON" and make sure to connect required power to VccQ and Vcc Lines
3.3v = Most New/Old Micro SD Cards are Compatible with 3.3v Vcc
1.8V = We have prepared a 1.8v Vcc for Future Low-Powered Micro SD Cards
[For eMMC Use Only]
NC = Secondary CLOCK will not be used for eMMC Communication
CLK2 = Secondary CLOCK will be used for eMMC Communication
When adapter is used for a NON-EMMC Connection such as JTAG or Micro SD Card, make sure this DIP Switch is on the "NC" Position.
CLK2 is NOT REQUIRED for most eMMC Chips, but setting DIP SWITCH to CLK2 will give you a stronger CLK (RED) Signal for better eMMC Communication.
Nokia disassembly tool included
Compatibility:
- ATF Nitro
- ATF Box (Big Metal Box)
- ATF Lightning
Set contains
1 X Official ATF Version 2 All in 1 Adapter for ATF Box
1 X Set of Coloured JTAG Wires
3 X FPC Ribbon Cables
1 X Lumia 510 / 610 Connector
1 X Molex port for Lumia 610/510 (needed because some 610 / 510 do not have molex already onboard)
2 X BGA PCB
1 X Nokia mini opening tool kit containing:
1 X Leaver / Opener for Nokia disassembly
1 X Screwdriver for Nokia disassembly
2 X Plastic opening picks for Nokia disassembly
1 X Suction cup
|
||
NEGOTIATE PRICE
If you are interested in
Adapter EMMC ATF V2 4in1
you will probably want to take a look at following products:
Other products from same category
+
|
Dual JTAG Cable set for ATF Metal/Gold
more
|
Price:
10.00 EUR w/o VAT |
+
|
EMMC Adapter for Nokia Lumia 535
more
|
Price:
18.00 EUR w/o VAT |
Dedicated equipments for this adapter:
+
|
ATF Nitro + ATF Network Account Activation
more
|
Price:
109.00 EUR w/o VAT |
See also
+
|
Lumia Test-Point for ATF cables set
more
|
Price:
19.00 EUR w/o VAT |
+
|
Lumia Test-Point for ATF 6 cables set
more
|
Price:
24.00 EUR w/o VAT |
+
|
Cable Lumia Test-Point for ATF
more
|
Price:
2.50 EUR w/o VAT |
+
|
ATF 5 in 1 EMMC Cable
more
|
Price:
6.00 EUR w/o VAT |
+
|
GPG EMMC JTAG Box Full + 33 JIG
more
|
Price:
199.00 EUR w/o VAT |
+
|
ATF Nitro SD Reader
more
|
Price:
6.00 EUR w/o VAT |
+
|
ATF JTAG EMMC activation
more
|
Price:
39.00 EUR w/o VAT |
+
|
Adapter EMMC/JTAG ATF v2 5in1 GPG
more
|
Price:
20.00 EUR w/o VAT |
+
|
Adapter ATF-SPI for Nokia 105/106
more
|
Price:
10.00 EUR w/o VAT |
+
|
Adapter MTBOX 10pin - ATF 8pin
more
|
Price:
7.00 EUR w/o VAT |
You might also be interested in:
+
|
ATF TP Finder
more
|
Price:
19.00 EUR w/o VAT |
+
|
Cyclone V2.0 PRO Adaptor
more
|
Price:
8.00 EUR w/o VAT |
+
|
HXCPRO Tool Green
more
|
Price:
19.00 EUR w/o VAT |
+
|
Converter FBUS/MBUS
more
|
Price:
9.35 EUR w/o VAT |
+
|
Adapter BB5 Universal Box with TX2 lines
more
|
Price:
9.00 EUR w/o VAT |
+
|
Infrared port i-tec IrDA USB
more
|
Price:
15.00 EUR w/o VAT |
+
|
GPG HUB Pro
more
|
Price:
30.00 EUR w/o VAT |
+
|
Adapter MT-BOX/GTI 10 pin - Cyclone Box
more
|
Price:
8.00 EUR w/o VAT |
This product was bought most often with:
|
+
|
Adapter ATF-SPI for Nokia 105/106
more
|
Price:
10.00 EUR w/o VAT |
|
+
|
ATF TP Finder
more
|
Price:
19.00 EUR w/o VAT |
+
|
ATF GOLD - Advance Turbo Flasher + ATF Network + JTAG EMMC
more
|
Price:
159.00 EUR w/o VAT |
+
|
Adapter GPG-FT232 dla GPG eMMC Box
more
|
Price:
39.00 EUR w/o VAT |
|
+
|
ATF Nitro + ATF Network Account Activation
more
|
Price:
109.00 EUR w/o VAT |
+
|
Universal adapter for JTAG Box
more
|
Price:
6.00 EUR w/o VAT |
+
|
Adapter for ATF 20PIN JTAG JIGS - RJ45
more
|
Price:
4.00 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.
