EMMC devices for reading devices in ISP and Direct Mode (Chip-Off)
EMMC memory devices are to facilitate communication over the JTAG, SD and MPHY protocol. EMMC stands for Embedded MultiMediaCard is an advanced NAND flash that is soldered directly to a motherboard or device. The devices allow it to read, write and repair data using the ISP but also Direct method. EMMC memories are found in phones, tablets, drones, telemetry and industrial devices. Data recovery from eMMC memory is performed by the NAND protocol from the technological pins.
22020 |
Easy Z3X Plus LITE (Easy Jtag Plus Box) Easy Z3X Plus LITE (Easy Jtag Plus Box) is the latest eMMC / JTAG interface of the already well-known Z3x group, whose Multi-COM company is the official representative. The interface created by it is a device that not only serves to repair the bootloader but also has a built-in PinFinder so that we can find the JTAG pinoout in a few seconds. The box also supports the full 8 bit ISP transmission in the latest version. In addition, the Box has a fully functional communication module Fbus and SPI, so it will be possible to flash the repaired phone without additional devices. |
21936 |
OctoPlus Pro Box Full (LG+SAM+JTAG+EMMC) 3in1 OctoPlus Pro Box Full (LG+SAM+JTAG+EMMC) 3in1 is a phone servicing solution that combines unibox and JTAG interfaces and supports over 530 Samsung, 900 LG and 460 by JTAG mobile devices. It can be used to unlock, flash and recover LG phones, resolve freeze problems and restore IMEI, NVM, camera and network. This box allows to complete support of A2 platform, contains advanced language pack editor as well as complete Softbank support. Box allows you to repair boot in LG 3G-Cyon-Show-FOMA and Anycall phones. OctoPlus Pro is JTAG/EMMC product for professional phone flashing and mobile unlocking tool that lets you work with a wide range of Samsung, Huawei, LG, Motorola, Siemens, Sony Ericsson, Vodafone, ZTE and other mobile devices through JTAG, USB and MMC interfaces. |
23057 |
Programator JCID U15 UFS is designed for work with BGA153, BGA254, BGA297 types of UFS2.X, 3.X, 4.X NAND chips. JCID UFS programmer provides reading, writing, capacity expansion and repair solutions to all series Android mobile phone with UFS chips. Compatible with V1SPro programmer. |
22780 |
Universal engineering programmer NuProg-E2 (eMMC, UFS, NAND, NOR) Universal engineering programmer NuProg-E2 (eMMC, UFS, NAND, NOR) widely supports most IC types on the market, UFS, eMMC, MCU, CPLD, FPGA, SPI NOR, SPI NAND, Parallel NOR, Parallel NAND and EEPROM, etc. And also support different types of IC packages: CSP, BGA, QFN, QFP, SOP, TSOP, SSOP, PLCC, DIP, etc. Designed FPGA kernel architecture supplies ultra high speed programming performance. The Programming project and sockets are compatible with NuProgPlus. Together with built-in SuperSpeed® USB 3.0 for high-speed communication, it is an efficient tool for you to focus on application analysis and product development. |
17203 |
GPG EMMC JTAG Box Full + 33 JIG GPG EMMC JTAG Box Full + 33 JIG is a box for repairing dead Android and WP8 phones with EMMC. The supported model range includes Samsung I9300/I9100, HTC G14, Sony, China ZTE/China Huawei/China MTK and thousands of other phones and brands. GPG EMMC support does not depend on the phone model. You can fulfill Read / Write operations with any phones that have a supported EMMC IC. |
14305 |
GPG EMMC JTAG Box is a box for repairing dead Android and WP8 phones with EMMC. The supported model range includes Samsung I9300/I9100, HTC G14, Sony, China ZTE/China Huawei/China MTK and thousands of other phones and brands. GPG EMMC support does not depend on the phone model. You can fulfill Read / Write operations with any phones that have a supported EMMC IC. |
16520 |
ATF GOLD - Advance Turbo Flasher + ATF Network + JTAG EMMC ATF GOLD (Advance Turbo Flasher) + ATF Network and JTAG EMMC activation by Advance Team it's a powerful tool which can flash all Nokia phones including new protocols via Fbus cable in unbelievable speed and stability in compare of any other 3rd party tool which currently present in market. New Protocols Device X3 ,X6 ,E52 ,E55 ,6700 ,etc and all Rapuyama Fbus Flashing. Ofcourse Repair Super dongle key, Repair Sim Lock Dat, UNLOCK are also available. Our version has got preactivated ATF Network support. Activation JTAG EMMC allows to use JTAg Tool with super easy interface and simple and effective repair procedure. Allows to repair all Nokia WP8 Lumia phones with spped up to 480 Mbps USB via ATF Box. |
22326 |
Easy Jtag Z3X Plus Ultimate 16in1 (JTAG/eMMC/UFS) Easy Jtag Z3X Plus Ultimate 16in1 (JTAG/eMMC/UFS) is a complete device for communication via JTAG, SD (read/write eMMC / eMCP) and MPHY protocol (read/write UFS). The Ultimate version consists of the Easy Z3x Plus interface with a set of 13in1 adapters for reading 99% of eMMC / eMCP systems together with 3in1 adapters for reading UFS (BGA 153, 95 and 254). The interface of the well-known Z3x group - of which Multi-COM is the official representative - not only serves to repair the bootloader but has a built-in PinFinder so that we can find the JTAG pinout in a few seconds. The box also supports the latest version of the full 4-bit ISP transmission and MPHY protocol (read / write UFS memory). In addition, the Box has a fully functional Fbus and SPI communication module, thanks to which it will be possible to flash a repaired phone without additional devices. |
22031 |
Easy Z3X Plus FULL (Easy Jtag Plus Box) Easy Z3X Plus FULL (Easy Jtag Plus Box) is the latest eMMC / JTAG interface of the already well-known Z3x group, whose Multi-COM company is the official representative. The interface created by it is a device that not only serves to repair the bootloader but also has a built-in PinFinder so that we can find the JTAG pinoout in a few seconds. The box also supports the full 8 bit ISP transmission in the latest version. In addition, the Box has a fully functional communication module Fbus and SPI, so it will be possible to flash the repaired phone without additional devices. |
22365 |
HYPOBOX- programmer for eMMC/UFS/NAND HYPOBOX- programmer for eMMC/UFS/NAND is a professional engineering tool for programming mass flash storage with its speed and reliability. |
17275 |
Medusa Pro Box (JTAG i EMMC) is leatest JTAG/EMMC product for professional phone flashing and mobile unlocking tool that lets you work with a wide range of Samsung, Huawei, LG, Motorola, Siemens, Sony Ericsson, Vodafone, ZTE and other mobile devices through JTAG, USB and MMC interfaces. The main intended purpose of Medusa PRO Box is repairing dead boots of the devices (mobile phones, PDAs, modems, etc.) or these devices recovery, until they become fully operational. Medusa PRO Box Software is a windows application for Medusa PRO Box, provides convenient interface for end user. |
17332 |
Medusa PRO Upgrade Kit is an upgrade kit for the owners of Medusa Box or Octoplus JTAG Box only! Please be aware, the following kit does NOT include smart card and activation. Medusa PRO is leatest JTAG/EMMC product for professional phone flashing and mobile unlocking tool that lets you work with a wide range of Samsung, Huawei, LG, Motorola, Siemens, Sony Ericsson, Vodafone, ZTE and other mobile devices through JTAG, USB and MMC interfaces. The main intended purpose of Medusa PRO Box is repairing dead boots of the devices (mobile phones, PDAs, modems, etc.) or these devices recovery, until they become fully operational. Medusa PRO Box Software is a windows application for Medusa PRO Box, provides convenient interface for end user. |
22630 |
MOORC MIPITESTER/MiPi Box Pro Programmer for EMMC and UFS MOORC MIPITESTER/MiPi Box Pro Programmer for EMMC and UFS is a UFS / eMMC device programmer designed to read / write and repair data using both the ISP and Direct method. The set includes UFS (297/254/153) and eMMC / eMCP (153-169, 254, 221, 162-186, 100, 136, 529, 168) adapters. |
21154 |
ORT EMMC Booster is high speed interface allowing read USER area partition from eMMC chips. eMMC Booster integrates a high speed microprocessor and a high efficiency hardware engine for the best data transfer performance between USB and eMMC interfaces. |
21170 |
ORT eMMc PRO + Emmc Booster set ORT eMMc PRO + Emmc Booster set it's full set dedicated for forensic use as also repair center for reapding eMMC , eMCP in ISP mode which enables users to directly recover the complete data without removing the chip. eMMC Pro HW and SW is able to access the eMMC every part / partitions and zones so you wont miss a spot ! eMMC Pro is designed for Low-Level Operations and designed for Professionals not just a Simple Reader. |
21223 |
ORT JTAG Pro with EMMC Booster ORT JTAG Pro with EMMC Booster is an advanced JTAG Programmer / Multi-brand JTAG tool, which lets you to work with the wide range of devices with the JTAG interface. The main intended purpose of the ORT JTAG Pro Edition is repairing / recovering dead boot of the devices such as mobile phones, smartphones, modems and other electronic devices, where you can get access to JTAG interface. eMMC Booster Tool allows you to Read / Write (user area) of eMMC Chipsets. eMMC Booster integrates a high-speed microprocessor and a high efficiency hardware engine for the best data transfer performance between USB and eMMC interfaces. Supports mobile phones in-system programming and provides required eMMC voltage. |
21723 |
Programmer UFS / eMMC / eMCP NuProg-E Programmer UFS / eMMC / eMCP NuProg-E is a universal programmer (read / write / verification) for the memory eMMC / EMCP and also to the latest UFS IC (used in Samsung S6, S6 Edge, Note 5, S7, S7 Edge) . Programmer equipped with its own easy-to-use Windows software allows for full configuration in case of UFS memory access and in case of eMMC / eMCP allows also to access to RPMB along with standard UserData, Boot, GPP and CSD partitions. |
21216 |
RIFF Box 2 - JTAG/EMMC/I2C ORIGINAL RIFF Box 2 - JTAG/EMMC/I2C ORIGINAL is the successor of the well-known Riff Box and is used to read and write memory eMMC / NAND using all kinds of communication protocols like eMMC (ISP Direct) / JTAG / I2C / SPI. Box fully supports 4-bit transmissions and allows you to read up to 52 MHz bus width . It is used for reading and recovery electronic devices as well as repair boot in phones / devices. |
21836 |
UFi Box - Worldwide version is the most advanced box for eMMC / eMMCP in Direct / ISP mode. Thanks to the very simple interface, you can repair eMMC devices much simpler that before (resize partition, format, smart test, read and write) and also repair your phones with ADB (HSQUSB 9008) and SPI software (NOR readings). |