 |
JTAG programmers, adapters and devices for communication with mobile phones. UFS / eMMC device programmer designed to read / write and repair data using both the ISP and Direct method. Communication takes place in various JTAG, SD or MPHY protocols. VR-TABLE enables communication, reading and writing of memory via EMMS, JTAG or communication in FBUS mode.
ORT EMMC Booster
5
(1)
ORT EMMC Booster is high speed interface allowing read/write USER area partition from eMMC chips. eMMC Booster integrates a high speed microprocessor and a high efficiency hardware engine for the best data transfer performance between USB and eMMC interfaces.
Specification:
High-speed USB 2.0 transmission (Comply w/480Mbps USB spec.rev. 2.0)
Operate @ 60 MHz clock / 12 clocks per instruction cycle
High speed Supporting 8 Bits with Compatible adapter and sockets
support eMMC Connection with Socket ( Chip-off )
support SD card Connection ( Direct SD )
Secure Digital and MultiMediaCard
Supports SD specification v1.0 / v1.1 / v2.0
Supports MMC specification v3.X / v4.X / v5.0 / v5.1
eMMC Booster Tool enable you to read/write ( user Area ) of eMMC Chipsets for diffrent purposes
Device Repair
Re-programm the chip for the various reasons
Replacement of Damaged chipset
Fix Failure of the Boot
Analyze Data
Read Plain Data for further investigation (Mobile Phone Forensic(s))
Set photo:
Package contains:
1 x eMMC Booster Box
2 x 20 Pin Flat Connection Cable
1 x activaiton code for software
1 x BGA 153 eMMC Break Out Board
1 x Pack of Tinned Soldering Wires
1 x Fine Soldering Wire Spool
Specification:
eMMC Booster Tool enable you to read/write ( user Area ) of eMMC Chipsets for diffrent purposes
Set photo:
Package contains:
1 x eMMC Booster Box
2 x 20 Pin Flat Connection Cable
1 x activaiton code for software
1 x BGA 153 eMMC Break Out Board
1 x Pack of Tinned Soldering Wires
1 x Fine Soldering Wire Spool
|
||
NEGOTIATE PRICE
Additional information about this product:
Information concerning technical requiments :The correct use of the purchased goods is required to have a stable internet connection with min . capacity of 1024 kb / s ( download) and 512 kb / s ( upload) . Before you attempt to make software update on the device or want to activate/use service, make sure that you have a sufficient link parameters .
Information concerning the interoperability of digital content:
For using a software or a piece of software that the manufacturer supplies with purchased hardware, in some cases it’s required that you disable your Firewall ( in software or router) and antivirus software. Leaving it enabled can occurs inproper operation of software / services and you will get communications errors like “Error 10060”.
.
Information concerning hardware requiments:
For proper working with this device producer suggest PC computer with 32-bit Windows XP operating system. We don't guarantee that software/device will work or any other system - especially 64-bit systems, iMac, Linux.
Information concerning IMEI change:
We want to inform that IMEI change option in softwares are intended to use only to repair broken IMEI and retrieve it to original state. It's prohibitted to use this function to change IMEI to diffrent that original. Multi-COM don't answer to any questions related with operation on IMEI number - if you require help in this metter please contact with software/device producer directly. We don't take any responsibility to use this function.
If you are interested in
ORT EMMC Booster
you will probably want to take a look at following products:
Suggested items for this device:
+
|
VR-TABLE for JTAG EMMC FBUS Tool
more
|
Price:
1099.00 EUR w/o VAT |
Other products from same category
+
|
RIFF Box JTAG/EMMC ORIGINAL
more
|
Price:
119.00 EUR w/o VAT |
+
|
GPG EMMC JTAG Box
more
|
Price:
169.00 EUR w/o VAT |
+
|
ATF JTAG EMMC activation
more
|
Price:
39.00 EUR w/o VAT |
+
|
Adapter GPG eMMC BGA 162
more
|
Price:
99.00 EUR w/o VAT |
+
|
EMMC adapter for Easy Z3x JTAG Box
more
|
Price:
12.00 EUR w/o VAT |
Suggested hardware for use with above set
Below you will find special hardware that it's suggested to use with this set.
+
|
Moorc E-Mate X 13in1 - ICFriend Edition
more
|
Price:
179.00 EUR w/o VAT |
You might also be interested in:
+
|
Easy Z3X Plus converter to the SE-P1 adapter
more
|
Price:
8.00 EUR w/o VAT |
+
|
ORT JTAG Pro with EMMC Booster
more
|
Price:
149.00 EUR w/o VAT |
+
|
ICFRIEND Easy-UFS 4in1 socket set
more
|
Price:
299.00 EUR w/o VAT |
+
|
Adapter for EPIC Programmer
more
|
Price:
12.54 EUR w/o VAT |
+
|
UFS BGA153 adapter for the Easy Z3x Plus
more
|
Price:
179.00 EUR w/o VAT |
+
|
Z3X Easy-Jtag Plus BGA-254 2-in-1 eMMC/UFS Socket Adapter
more
|
Price:
145.00 EUR w/o VAT |
+
|
Flat tape 20 pin for JRT/ORT/RIFF
more
|
Price:
3.50 EUR w/o VAT |
+
|
UFi Box - Worldwide version
more
|
Price:
309.00 EUR w/o VAT |
This product was bought most often with:
+
|
Universal JTAG/eMMC/FBUS JE-02 adapter
more
|
Price:
20.00 EUR w/o VAT |
+
|
Adapter for ATF 20PIN JTAG JIGS - RJ45
more
|
Price:
4.00 EUR w/o VAT |
+
|
Multicolored F-F cables 17 cm to the contact plate - 40 pcs
more
|
Price:
4.20 EUR w/o VAT |
+
|
JTAG for Samsung i8190/i8190N (Galaxy S3 mini/NFC)
more
|
Price:
10.00 EUR w/o VAT |
+
|
Adapter EMMC for Riff BOX (RC1000)
more
|
Price:
25.00 EUR w/o VAT |
+
|
Power supply cable for Riff JTAG
more
|
Price:
3.00 EUR w/o VAT |
|
+
|
Moorc E-Mate X 13in1 - ICFriend Edition
more
|
Price:
179.00 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.
