Programmers / JTAG
JTAG programmers, adapters and devices for communication with mobile phones. UFS / eMMC device programmer designed to read / write and repair data using both the ISP and Direct method. Communication takes place in various JTAG, SD or MPHY protocols. VR-TABLE enables communication, reading and writing of memory via EMMS, JTAG or communication in FBUS mode.
21836 |
UFi Box - Worldwide version is the most advanced box for eMMC / eMMCP in Direct / ISP mode. Thanks to the very simple interface, you can repair eMMC devices much simpler that before (resize partition, format, smart test, read and write) and also repair your phones with ADB (HSQUSB 9008) and SPI software (NOR readings). |
17327 |
VR-TABLE for JTAG EMMC FBUS Tool VR-TABLE for JTAG/EMMC/FBUS Tool is a precision tool for non-invasive ISP (ie, In System Programming) Reading and writing via EMMC, JTAG which replaces the need for soldering or desoldering anything in motherboard. VRTable enables forensic examiners to acquire data from Mobile Devices, GPS Devices and other electronics units. Optimization is based on a fully individually configurable VR-ARMS ended precision probes and additional reference voltages for all types of memory. VRTable can be also freely used in the car diagnostics (car radios, controllers) as well as in FBUS communication mode - completely replacing the RJ45/RJ48 cables. |
16639 |
Dual JTAG Cable set for ATF Metal/Gold Dual JTAG Cable set for ATF Metal/Gold is a set of cables 8 and 10 pin for boxes ATF Metal and Gold allows you to operate on mobile via JTAG two phones at the same time . Cable 8 pin schould be connected to the socket FlashBus and 10 pin cable to the EXTENSION socket . Cable includes VBATT 4.0V output so you don't need external power supply for phone powering from DC power supply. |
7584 |
Flat tape 20 pin for JRT/ORT/RIFF Flat tape 20 pin for JRT/ORT/RIFF it's connection flat tape to connect JTAG adapters with JRT SMTI adapter, Riff Box or Omnia Repair Tool. |
21231 |
Adapter eMMC/JTAG for Riff BOX 2 - RC2000 Adapter eMMC/JTAG for Riff BOX 2 - RC2000 allows a very simple repair phones by JTAG using IDC20 pin connector known from previous riff but offers also support for eMMC using leatest 30 pin connector (IDC 30 pin). By this you can repair phones with blocked JTAG access (GT-i9300 / N7100 / N719 / N7102, etc.), repair phones with damaged JTAG points/pads (access to ROM2 by EMMC) or read/write EMMC applicable for the data recovery/analysis. Using the adapter you can perform format EMMC or low-format (in case of damage EMMC), CMD42 Lock/Unlock/Pasword reset or Samsung eMMC Factory Format. Our adapter allows you to connect in ISP mode (directly onto your phone without removing the EMMC) or Direct (by removing the BGA soldering and the corresponding memory fields or using adapter). |
1035 |
Adapter for EPIC Programmer enable you to connect 28 pin's DIp chipset to your EPIC programmer |
15020 |
Adapter GPG-FT232 dla GPG eMMC Box Adapter GPG-FT232 dla GPG eMMC Box is to solve all of connectivity ISP issue such as: eMMC ORC: 00000000, bad code ! >> Id check lost. |
1037 |
AVR Programmer it's a very good device programmer. If you are looking for a simple but powerful programmer you are right, it's here. AVR it's a parell programmer software with a user friendly GUI framework available for Windows95, 98, XP, 2000 & NT and Intel Linux. Its purpose is reading and writing Atmel AVR using system provides a standard In System Programming (ISP) connector. The PC interface is through the Parallel port, and makes use of the same pinout as the STK-200 programmer from Kanada Systems. The STK-200 programming cable is very popular, and almost every ISP download software (Except ICCAVR's inbuilt chip programmer) supports it. |
22626 |
Easy Z3X Plus converter to the SE-P1 adapter Easy Z3X Plus converter to the SE-P1 adapter allows you to use the soldered adapter supplied with the Easy Z3x Plus box in order to connect it with the SE-P1 adapter and the SD card reader. The solution is useful when performing images and tests with the use of other software for SD eMMC ISP without the need to desolder the already made connection. |
22020 |
Easy Z3X Plus LITE (Easy Jtag Plus Box) Easy Z3X Plus LITE (Easy Jtag Plus Box) is the latest eMMC / JTAG interface of the already well-known Z3x group, whose Multi-COM company is the official representative. The interface created by it is a device that not only serves to repair the bootloader but also has a built-in PinFinder so that we can find the JTAG pinoout in a few seconds. The box also supports the full 8 bit ISP transmission in the latest version. In addition, the Box has a fully functional communication module Fbus and SPI, so it will be possible to flash the repaired phone without additional devices. |
22726 |
eMMC/UFS ICFriend AndroidKing Adapter Set 9in1 + AK5 eMMC/UFS ICFriend AndroidKing Adapter Set 9in1 + AK5 is a set of eMMC / UFS adapters for reading eMMC and UFS bones along with AK5 (Easy JTAG Plus) adapter . The set allows to read nearly 90% of BGA chips available on the market, such as eMMC / eMCP BGA 153, 169, 162, 221, 254, 186 as well as UFS BGA 153, 254, 95 chips |
1034 |
EPIC Plus Programmer is available assembled and tested. Programmer quickly and easily programs the mid-range PICmicros, including the PIC16C55x, 6xx, 7xx, 84, 9xx, PIC16CE62x, PIC16F8xx, PIC14Cxxx, the 8-pin PIC12Cxxx, PIC12CExxx and the 14-pin 16C505 microcontrollers. The basic programmer includes an 18-pin socket for programming 8-, 14- and 18-pin PICmicros. ZIF adapters are available to program 28- and 40-pin as well as surface mount and PLCC packaged PICmicros. (It will not program or read the base-line PIC16C5x or high-end 17Cxxx series.) |
8290 |
GPG HWK Repair Dongle is a tool allows you to perform one-click repair of HWK software problems like HWK Dead, HWK Not connected etc. in case it's software failure. HWK Repair Dongle does not clone HWK HID, therefore it can be used for original HWK without loss of warranty. |
22760 |
ICFRIEND AK1 eMMC Adapter for Z3X Easy Jtag Plus Box ICFRIEND AK1 eMMC Adapter for Z3X Easy Jtag Plus Box This adapter allows the owners of Z3X Easy Jtag Plus Box to work with: Androidking AK-BGA eMMC 11 in 1 Adapter AND Androidking AK-BGA eMMC 15 in 1 Adapter. Read / Write / Repair data (full eMMC support, including 8-bit bus) |
22759 |
ICFRIEND AK5 UFS Adapter for Z3X Easy Jtag Plus Box ICFRIEND AK5 UFS Adapter for Z3X Easy Jtag Plus Box This adapter allows the owners of Z3X Easy Jtag Plus Box to work with: Androidking AK-BGA eMMC 11in1 Adapter and Androidking AK-BGA eMMC 15in1 Adapter for Read / Write / Repair data*. |
23153 |
ICFriend UFS Socket 3in1 set (297/153/254) for Z3X Easy Jtag Plus ICFriend UFS Socket 3in1 set for Z3X Easy Jtag Plus will enable the user to work with newer UFS chipsets, and let you read data / write data etc. ICFriend Supports: UFS BGA153 Chip, UFS EMMC BGA254 Chip and UFS BGA297 Chip. |
23152 |
ICFriend UFS Socket 6w1 set for Z3X Easy Jtag Plus ICFriend UFS Socket 6w1 set for Z3X Easy Jtag Plus will enable the user to work with newer UFS chipsets, and let you read data / write data etc. ICFriend Supports: UFS BGA153 Chip, UFS EMMC BGA254 Chip and UFS BGA297 Chip. |
21775 |
JTAG/eMMC ISP 4in1 Adapter Kit MOORC 2018 JTAG/eMMC ISP 4in1 Adapter Kit MOORC 2018 is a set of adapters that offer direct programming (BGA162 / 186, BGA 153/169 and BGA 221) with Riff, Easy Z3x JTAG, ORT, GPG as well as use JTAG communication. |
22625 |
Medusa Pro II Nand Adapter TSOP-48/LGA-52/LGA-60 Medusa Pro II Nand Adapter TSOP-48/LGA-52/LGA-60 is intended for reading/writing/erasing NAND data via soldering. Supported ICs: TSOP-48, LGA-52, LGA-60. |
22089 |
Moorc E-Mate X 13in1 - ICFriend Edition Moorc E-Mate X 13in1 - ICFriend Edition is the latest version of a set of adapters allowing for direct eMMC memory connection and read and/or write it contest. Adapter/Socket is fully compatible with many eMMC devices, such as Riff Box, Riff Box 2, Medusa Pro Box, Z3X Easy Jtag Box, Easy Z3x Plus, GPG EMMC Box, UFi Box, etc. The new version in comparison to the 2017 edition allows in addition to previously supported pinouts also reading the latest eMMCs BGA254, BGA100, BGA136, BGA168. |