 |
JTAG programmers, adapters and devices for communication with mobile phones. UFS / eMMC device programmer designed to read / write and repair data using both the ISP and Direct method. Communication takes place in various JTAG, SD or MPHY protocols. VR-TABLE enables communication, reading and writing of memory via EMMS, JTAG or communication in FBUS mode.
AVR Programmer
AVR Programmer it's a very good device programmer. If you are looking for a simple but powerful programmer you are right, it's here. AVR it's a parell programmer software with a user friendly GUI framework available for Windows95, 98, XP, 2000 & NT and Intel Linux. Its purpose is reading and writing Atmel AVR using system provides a standard In System Programming (ISP) connector. The PC interface is through the Parallel port, and makes use of the same pinout as the STK-200 programmer from Kanada Systems. The STK-200 programming cable is very popular, and almost every ISP download software (Except ICCAVR's inbuilt chip programmer) supports it.
This AVR Interface is ready to program following chips:
Support AT90S1200, AT90S2313, AT90S2323, AT90S2343, AT90S4414, AT90S4434, AT90S8515, AT90S8535 Flash micro
Support AT90S2323, AT90S2343, AT90S2333, AT90S4433, AT90S4434, AT90S8535, AT90S8534
Support the AVR microcontroller ATmega103, ATmega161, ATmega163, ATmega 323, ATmega128, ATmega8
Support the AVR microcontroller ATmega16, ATmega64 (untested)
Support the AVR microcontroller ATmega32, ATmega162, ATmega 169, ATmega8515, ATmega8535 (untested)
Support the AVR ATtiny microcontroller ATtiny12, ATtiny15
Read ATtiny12 and ATtiny15 Oscillator Calibration Byte
Support the AT89S8252 and AT89S53 micro
About used software:
Software compatible with this programmer includes AVR ISP from Atmel, a very good device programmer. It can read/write the Flash and EEPROM, and set the security bits. It includes a nice "Autoprogram" command, that reloads all the device files and downloads the ones that have changed to the AVR. PonyProg, by Claudio Lanconelli, another nice programmer, a bit slower than AVRISP. However, it can be used to program lots of other types of devices, such as EPROMS, serial EEPROMS, etc. CodeVisionAVR C compiler's inbuilt chip programmer, by HP Infotech, has the advantage of being a part of the compiler IDE.
AVR-ISP pinouts Pin Description:
RESET - Used to reset the target system under the PC's control.
SCK - The serial data clock
MOSI Master Out Slave In - used to send data from the PC (master) to the AVR (slave). Data is transmitted on the edges of SCK.
MISO Master In Slave Out - used to send data from the AVR (master) to the PC (slave). Data is transmitted on the edges of SCK.
LED The PC - makes this line high to indicate that programming is occuring. Not used in all systems.
PWR - Can be used either to provide power to the target system during programming, or for the programmer to draw power from the target system during programming. I use it to allow the programmer to draw power from the system.
Complete contains:
AVR programmer
FLAT cable for connecting chips
warranty card
This AVR Interface is ready to program following chips:
About used software:
Software compatible with this programmer includes AVR ISP from Atmel, a very good device programmer. It can read/write the Flash and EEPROM, and set the security bits. It includes a nice "Autoprogram" command, that reloads all the device files and downloads the ones that have changed to the AVR. PonyProg, by Claudio Lanconelli, another nice programmer, a bit slower than AVRISP. However, it can be used to program lots of other types of devices, such as EPROMS, serial EEPROMS, etc. CodeVisionAVR C compiler's inbuilt chip programmer, by HP Infotech, has the advantage of being a part of the compiler IDE.
AVR-ISP pinouts Pin Description:
RESET - Used to reset the target system under the PC's control.
SCK - The serial data clock
MOSI Master Out Slave In - used to send data from the PC (master) to the AVR (slave). Data is transmitted on the edges of SCK.
MISO Master In Slave Out - used to send data from the AVR (master) to the PC (slave). Data is transmitted on the edges of SCK.
LED The PC - makes this line high to indicate that programming is occuring. Not used in all systems.
PWR - Can be used either to provide power to the target system during programming, or for the programmer to draw power from the target system during programming. I use it to allow the programmer to draw power from the system.
Complete contains:
Warranty
This product has 12 months warranty.
|
||
NEGOTIATE PRICE
Additional information about this product:
Information concerning technical requiments :The correct use of the purchased goods is required to have a stable internet connection with min . capacity of 1024 kb / s ( download) and 512 kb / s ( upload) . Before you attempt to make software update on the device or want to activate/use service, make sure that you have a sufficient link parameters .
Information concerning the interoperability of digital content:
For using a software or a piece of software that the manufacturer supplies with purchased hardware, in some cases it’s required that you disable your Firewall ( in software or router) and antivirus software. Leaving it enabled can occurs inproper operation of software / services and you will get communications errors like “Error 10060”.
.
Information concerning hardware requiments:
For proper working with this device producer suggest PC computer with 32-bit Windows XP operating system. We don't guarantee that software/device will work or any other system - especially 64-bit systems, iMac, Linux.
Information concerning IMEI change:
We want to inform that IMEI change option in softwares are intended to use only to repair broken IMEI and retrieve it to original state. It's prohibitted to use this function to change IMEI to diffrent that original. Multi-COM don't answer to any questions related with operation on IMEI number - if you require help in this metter please contact with software/device producer directly. We don't take any responsibility to use this function.
If you are interested in
AVR Programmer
you will probably want to take a look at following products:
See also
+
|
GPG HWK Repair Dongle
more
|
Price:
22.00 EUR w/o VAT |
This product was bought most often with:
+
|
Adapter for EPIC Programmer
more
|
Price:
12.54 EUR w/o VAT |
+
|
Cable for Panasonic X70 COM
more
|
Price:
10.00 EUR w/o VAT |
+
|
EPIC Plus Programmer
more
|
Price:
25.29 EUR w/o VAT |
+
|
ERI RJ45 Tornado/Twister
more
|
Price:
5.00 EUR w/o VAT
12.30 EUR
|
+
|
Maxon 6810 v2.0,v3.0 cable
more
|
Price:
4.25 EUR w/o VAT |
+
|
MOT E365 v2.0,v3.0
more
|
Price:
4.25 EUR w/o VAT |
+
|
MOT V60/V66/V70 REPAIR v2.0, v3.0 cable
more
|
Price:
6.80 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.
