|
Main page > Data Analysis and Forensic Tools > VR-TABLE > VR-Table eMMC/eMCP/JTAG ISP > VR-TABLE for JTAG EMMC FBUS Tool
|
 |
VR-TABLE for JTAG EMMC FBUS Tool
4.7
(3)
VR-TABLE for JTAG/EMMC/FBUS Tool is a precision tool for non-invasive ISP (ie, In System Programming) Reading and writing via EMMC, JTAG which replaces the need for soldering or desoldering anything in motherboard. VRTable enables forensic examiners to acquire data from Mobile Devices, GPS Devices and other electronics units. Optimization is based on a fully individually configurable VR-ARMS ended precision probes and additional reference voltages for all types of memory. VRTable can be also freely used in the car diagnostics (car radios, controllers) as well as in FBUS communication mode - completely replacing the RJ45/RJ48 cables.
VR-TABLE specification (depends on option) :
equipied with 7 or 10* 300 mm (VR-ARMS) with hydraulic (central) block, ended with precise tips for read/write via ISP JTAG/EMMC as also using FBUS. Each of Varms can be freely configured/placed along target motherboard
10 mm thick polished guides handles with lock system ensures optimal placement of equipment at the desired location
central VR-ARM allows locate the servicing device (JTAG, EMMC BOxex) safely without fear of his movement exactly over a target - by this you are close to target and avoid communication errors
* Light with a magnifying glass and glass lens 5D MA-1225CF: AC230V, dustproof cover to protect the lens. 22-watt T5 loader. The flexible arm allows any change angle and direct the light where you need it most
high quality plastic finished non-slip pads, which absorb vibrations and oscillations
set of 10 embedded on-board channels with gold-plated connectors (L1, L2 .... / R1, R2 ....) connected to the socket IDC 10 that can be used in any TTL/FBUS communicatiions
2-2 banane type of cables that allows to sniff communication by puttign each cable into one., ie: osciloscope
onboard USB connection cable for better cable routing
internal voltage VCC/VCCQ build-in for EMMC/JTAG (3,3V, 2,85V, 1,8V)
maked from high quality of TecaForm AH Black and brushed aluminium
*options
Dedicated for:
forensic examiners and forensic laboratories
investigators and court experts
Electronic services: phones, tablets, car radios, GPS and other electronic devices
car diagnostics
diagnostics equipment: replacing cables communication FBUS
Universal Tool for all devices, ie:
• EMMC Pro Tool
• GPG EMMC
• ORT JTAG Pro with EMMC Tool
• Z3X Easy Jtag
• Riff Box
• Medusa Pro Box
• Medusa Box
• ATF i innne
• Martech Clip / Martech BOX III
Information about configurations:
• EMMC: 7 VRArms version needed
• JTAG: 10 VRArms version needed
• FBUS/TTL: 10 VRArms version needed
Photos with description of device:
VCC/VCCQ outputs 3,3, 2.85, 1,8
TTL/IDC connector from L1, L2... / R1, R2 sockets
Communications channels for TTL/FBUS connection with full description
Back USB routing allows easy USB device connection to table
10 mm thick polished guides handles with lock system ensures optimal placement of equipment at the desired location.
VR-ARMS: equipied with 7 or 10* 300 mm (VR-ARMS) with hydraulic (central) block, ended with precise tips for read/write via ISP JTAG/EMMC as also using FBUS. Each of Varms can be freely configured/placed along target motherboard
Central VR-ARM allows locate the servicing device (JTAG, EMMC BOxex) safely without fear of his movement exactly over a target - by this you are close to target and avoid communication errors
Available with magnifying glass and glass lens 5D MA-1225CF: AC230V, dustproof cover to protect the lens. 22-watt T5 loader. The flexible arm allows any change angle and direct the light where you need it most
Complete of 7 ARM edition:
- VR-Table main unit
- 6 VRArms 300mm for JTAG/EMMC/FBUS
- 8 probes for putting into VR Arms
- 6 communication cables banana of use with FBUS/VCC/VCCq
- 1 x VR Holder ARM
- 1 x VR holder for devices
- 1 x Universal JE-02 RJ45/Rj48/IDC 20 pin adapter for various devices with config page
- 1 x 17cm connection cables for signal routing from JE-02 adapter
- USB ferrite cable
- TORX key
- Suit case where VR can be stored for travel
- PROSKIT lamp with a magnifying glass 5D*
* - options
Complete of 7 ARM edition:
- VR-Table main unit
- 9 VRArms 300mm for JTAG/EMMC/FBUS
- 11 probes for putting into VR Arms
- 9 communication cables banana of use with FBUS/VCC/VCCq
- 1 x VR Holder ARM
- 1 x VR holder for devices
- 1 x Universal JE-02 RJ45/Rj48/IDC 20 pin adapter for various devices with config page
- 1 x 17cm connection cables for signal routing from JE-02 adapter
- USB ferrite cable
- TORX key
- Suit case where VR can be stored for travel
- PROSKIT lamp with a magnifying glass 5D*
* - options
We offer 12 months warranty for this product
VR-TABLE specification (depends on option) :
*options
Dedicated for:
Universal Tool for all devices, ie:
• EMMC Pro Tool
• GPG EMMC
• ORT JTAG Pro with EMMC Tool
• Z3X Easy Jtag
• Riff Box
• Medusa Pro Box
• Medusa Box
• ATF i innne
• Martech Clip / Martech BOX III
Information about configurations:
• EMMC: 7 VRArms version needed
• JTAG: 10 VRArms version needed
• FBUS/TTL: 10 VRArms version needed
Photos with description of device:
VCC/VCCQ outputs 3,3, 2.85, 1,8
TTL/IDC connector from L1, L2... / R1, R2 sockets
Communications channels for TTL/FBUS connection with full description
Back USB routing allows easy USB device connection to table
10 mm thick polished guides handles with lock system ensures optimal placement of equipment at the desired location.
VR-ARMS: equipied with 7 or 10* 300 mm (VR-ARMS) with hydraulic (central) block, ended with precise tips for read/write via ISP JTAG/EMMC as also using FBUS. Each of Varms can be freely configured/placed along target motherboard
Central VR-ARM allows locate the servicing device (JTAG, EMMC BOxex) safely without fear of his movement exactly over a target - by this you are close to target and avoid communication errors
Available with magnifying glass and glass lens 5D MA-1225CF: AC230V, dustproof cover to protect the lens. 22-watt T5 loader. The flexible arm allows any change angle and direct the light where you need it most
Complete of 7 ARM edition:
- VR-Table main unit
- 6 VRArms 300mm for JTAG/EMMC/FBUS
- 8 probes for putting into VR Arms
- 6 communication cables banana of use with FBUS/VCC/VCCq
- 1 x VR Holder ARM
- 1 x VR holder for devices
- 1 x Universal JE-02 RJ45/Rj48/IDC 20 pin adapter for various devices with config page
- 1 x 17cm connection cables for signal routing from JE-02 adapter
- USB ferrite cable
- TORX key
- Suit case where VR can be stored for travel
- PROSKIT lamp with a magnifying glass 5D*
* - options
Complete of 7 ARM edition:
- VR-Table main unit
- 9 VRArms 300mm for JTAG/EMMC/FBUS
- 11 probes for putting into VR Arms
- 9 communication cables banana of use with FBUS/VCC/VCCq
- 1 x VR Holder ARM
- 1 x VR holder for devices
- 1 x Universal JE-02 RJ45/Rj48/IDC 20 pin adapter for various devices with config page
- 1 x 17cm connection cables for signal routing from JE-02 adapter
- USB ferrite cable
- TORX key
- Suit case where VR can be stored for travel
- PROSKIT lamp with a magnifying glass 5D*
* - options
Warranty
We offer 12 months warranty for this product
|
||
NEGOTIATE PRICE
If you are interested in
VR-TABLE for JTAG EMMC FBUS Tool
you will probably want to take a look at following products:
Dedicated devices for this cable
+
|
USB cable Prolific PL2303X with 4mm banana connectors VR70/73M
more
|
Price:
15.00 EUR w/o VAT |
Available also additional modules:
+
|
Set of 10 standard probes VR-070 1mm/73mm to VR-Table
more
|
Price:
50.00 EUR w/o VAT |
+
|
Set of 10 ultra probes VR-073m 0,50mm/73mm to VR-Table
more
|
Price:
99.00 EUR w/o VAT |
+
|
Set of 10 high-precision probes with movable pins VR-064 1mm / 69mm to VR-Table
more
|
Price:
89.00 EUR w/o VAT |
+
|
Prolific PL2303X USB cable with FF connectors (VR64)
more
|
Price:
20.00 EUR w/o VAT |
+
|
USB cable (D+, D-, 5V, GND) with FF cables (VR64M)
more
|
Price:
15.00 EUR w/o VAT |
+
|
Universal PullUp PU eMMC cable for VR-Table (VR64)
more
|
Price:
20.00 EUR w/o VAT |
Other products from same category
+
|
RIFF Box 2 - JTAG/EMMC/I2C ORIGINAL
more
|
Price:
159.00 EUR w/o VAT |
Suggested items for this device:
+
|
ORT EMMC Booster
more
|
Price:
39.00 EUR w/o VAT |
Suggested hardware for use with above set
Below you will find special hardware that it's suggested to use with this set.
+
|
Inspection camera for VR-Table - VGA 2Mpx with holder
more
|
Price:
229.00 EUR w/o VAT |
See also
+
|
Universal eMMC PullUp PU cable for ISP eMMC to VR-Table (VR70/VR73M)
more
|
Price:
20.00 EUR w/o VAT |
+
|
RIFF Box JTAG/EMMC ORIGINAL
more
|
Price:
119.00 EUR w/o VAT |
+
|
Programmer UFS / eMMC / eMCP NuProg-E
more
|
Price:
1149.00 EUR w/o VAT |
+
|
Passware Kit Forensic
more
|
Price:
1095.00 EUR w/o VAT |
+
|
Medusa Pro Box (JTAG i EMMC)
more
|
Price:
159.00 EUR w/o VAT |
+
|
GPG EMMC JTAG Box Full + 33 JIG
more
|
Price:
199.00 EUR w/o VAT |
+
|
GPG EMMC JTAG Box
more
|
Price:
169.00 EUR w/o VAT |
+
|
ATF GOLD - Advance Turbo Flasher + ATF Network + JTAG EMMC
more
|
Price:
159.00 EUR w/o VAT |
You might also be interested in:
+
|
Set of Universal JTAG adapters VF-JIG for VR-Table - 11R
more
|
Price:
219.00 EUR w/o VAT |
+
|
VRArm 300mm for VR-Table
more
|
Price:
80.00 EUR w/o VAT |
|
+
|
Inspection camera for VR-Table - VGA 2Mpx with holder
more
|
Price:
229.00 EUR w/o VAT |
+
|
Holder for inspection camera used in VR-Table
more
|
Price:
50.00 EUR w/o VAT |
+
|
Inspection camera RF for VR-Table - 4K with holder
more
|
Price:
269.00 EUR w/o VAT |
This product was bought most often with:
|
+
|
Set of 10 ultra probes VR-073m 0,50mm/73mm to VR-Table
more
|
Price:
99.00 EUR w/o VAT |
|
+
|
Inspection camera for VR-Table - VGA 2Mpx with holder
more
|
Price:
229.00 EUR w/o VAT |
|
+
|
Universal eMMC PullUp PU cable for ISP eMMC to VR-Table (VR70/VR73M)
more
|
Price:
20.00 EUR w/o VAT |
|
+
|
Set of 10 high-precision probes with movable pins VR-064 1mm / 69mm to VR-Table
more
|
Price:
89.00 EUR w/o VAT |
|
+
|
Set of Universal JTAG adapters VF-JIG for VR-Table - 11R
more
|
Price:
219.00 EUR w/o VAT |
|
+
|
RIFF Box 2 - JTAG/EMMC/I2C ORIGINAL
more
|
Price:
159.00 EUR w/o VAT |
|
+
|
USB cable Prolific PL2303X with 4mm banana connectors VR70/73M
more
|
Price:
15.00 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.
