Main page > GSM products > Data and Unlock Cables > Xpin Clip, IP BOX, MFC > OS800 Adapter for XPIN Clip (iOS 8.0 - 8.1)
|
OS800 Adapter for XPIN Clip (iOS 8.0 - 8.1)
Features:
- Read PassCode of phones based on IOS 8.0 - 8.1 without disassembly phone
- Bypass enablding trigger removing data at 10 times the incorrect code is entered
Timing between entering next passcode after restart:
- iPhone 4S - 60 sek
- iPhone 5/5S - 50 sek
- iPhone 6/6+ - 40 sek
Note: 30 pin connector in 3in1 cable that is selling with XPIN Clip not working with unlimited attempts method. With Adapter iOS 8.0 - 8.1 you get other 30 pin USB HOST cable that working with this method (charging is not available).
Instruction for OS 800
1. Place the phone into the adapter and using clamps fix phone into adapter
2. Connect the power adapter to OS800 - USB B
3. Use the USB cable to connect the OS 800 adapter to the Charging port in XPIN Clip
4. Connect expansion port in Clip with connector on OS 800
5. After you successfully connect and press SET button on XPIN clip, all servos responsible for pressing the HOME and POWER, will set to the default position.
6. Connect via USB HOST cable (30 or 8 pin depending on the phone) iPhone with XPIN clip
7. Your phone should show the message that XPIN Clip has been detected
8. Go to the menu 8.0-8.1 IOS in XPN then go to submenu HEIGHT and press the SET button, start the procedure of setting height of HOME button on your phone using the DOWN button until the button is pressed. (Procedure best done on a blank screen when you press the HOME button the phone should awake) when this happens, press the SET button again
9. In the event of too strong tightening the HOME button, you can adjust the height of HEIGHT, pressing the SET button and use the UP lift the pressing frame.
10. To verify that the HOME button is set correctly, press the SET button when the phone responds again press the SET will lift the frame up, procedure must be repeated several times - if every time the HOME button is pressed, it means that it has been correctly set .
11. Go to submenu POWER BTN and select a page which is powering the phone (optional TOP - top, RIGHT - right) - make the selection by pressing the SET and directional up or down to select the desired button.
12. From the submenu PHONE selected phone model that has been placed in the adapter to the elections 4 / 4S 5 / 5S, 6 / 6P, we also changes by pressing the SET button.
NOTE: Parameters settings: 4 / 4S - 60 seconds 5 / 5S -50 seconds, 6 / 6P - 40 seconds (this is the interval after which followed the introduction of the next code to the phone and reset it) NOTE! These parameters MUST NOT be identical to the phone which is currently located in the adapter IOS 800, PHONE parameter can be used alternately, ie. Having placed in the adapter iPhone 6, you can choose 4 / 4S the waiting time for the next code will be set to 60 seconds.
Complete contains:
- adapter OS800
- USB A-B cable
- OTG 30 pin cable
|
NEGOTIATE PRICE
Dedicated equipments for this adapter:
+ |
XPIN Clip with cables set
more
|
Price:
349.00 EUR w/o VAT |
Other products from same category
+ |
XPIN upgrade firmware USB cable - A-A
more
|
Price:
3.49 EUR w/o VAT |
See also
+ |
reSTART Adapter for XPIN Clip
more
|
Price:
199.00 EUR w/o VAT |
+ |
Pattern Adapter for XPIN Clip
more
|
Price:
60.00 EUR w/o VAT |
You might also be interested in:
+ |
Flat Tape for XPIN Clip Pattern Adapter
more
|
Price:
3.00 EUR w/o VAT |
+ |
Micro USB Cable - USB OTG with simultaneous charge for XPIN Clip
more
|
Price:
7.00 EUR w/o VAT |
+ |
Pattern Adapter for XPIN Clip
more
|
Price:
60.00 EUR w/o VAT |
+ |
Charging Cable 3in1 for MFC Dongle
more
|
Price:
29.00 EUR w/o VAT |
+ |
XPIN Charging cable for Android
more
|
Price:
7.00 EUR w/o VAT |
+ |
XPIN upgrade firmware USB cable - A-A
more
|
Price:
3.49 EUR w/o VAT |
+ |
TRC sensor light cable for XPIN Clip
more
|
Price:
7.00 EUR w/o VAT |
+ |
Cable for Nokia 6820 COMBO Rj45/RJ48 For JAF®/MT-Box 2w1
more
|
Price:
6.50 EUR w/o VAT |
This product was bought most often with:
+ |
Pattern Adapter for XPIN Clip
more
|
Price:
60.00 EUR w/o VAT |
+ |
XPIN Clip with cables set
more
|
Price:
349.00 EUR w/o VAT |
+ |
Activation set RT-82 for iPhone 6 6+ 5 5c 5s 4s 4 / iPad
more
|
Price:
19.00 EUR w/o VAT |
+ |
Cut Blade/Knife for OCA/LOCA MC-MM82 - 82mm
more
|
Price:
1.20 EUR w/o VAT |
+ |
LCD Opener long version
more
|
Price:
8.00 EUR w/o VAT |
+ |
iP-Box iOS8 Adapter
more
|
Price:
55.00 EUR w/o VAT |
+ |
Universal XC2B charging battery adapter
more
|
Price:
22.00 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.