 |
reSTART Adapter for XPIN Clip
reSTART Adapter for XPIN Clip is used to restart phone with Android after a certain number of attempts to enter the code. Many Samsung Galaxy with a standard TouchWiz overlay has a bug, which cause jams of interface after approx. 25-50 entered codes which prevents the correct bruteforce attack on the PIN. Solution for this is restart phone after 10-20 codes. The adapter can also be used to reset the counter on Android phones 6.x.x, after entering the 10 codes, where each new code can be entered only after 30 seconds. Running phone again, we can again enter 10 codes (including the 30 seconds between successive 5 codes), so that the attack on the 4 pin code can be reduced from approximately 84 hours (120 codes per hour) to 24 hours (420 codes) take into account the average time to start a phone .
Features:
- Allows an attack on the PIN code preventing "jam" TouchWiz interface
- Shortens the time of the attack on some versions of Android 6.x.x
Specification
Material: TECAFORM, brushed aluminum
Power supply: miniUSB port (min. 1000 mA)
Communication Interface: IDC 26 pin - Extension Port XPIN Clip
Holder width (maximum width of mounted phone): 80 mm
Supported placement of POWER buttons: top, right, bottom
Type of servo: professional, metal modes
Adapter connected to XPIN Clip
Instruction:
1. Connect the reSTART adapter with IDC 26 cable to XPIN clip, then connect the 5V power supply to the mini USB (use charger with min. 1A), connect the power supply to XPIN Clip (USB B).
2. Select Android PIN and then the submenu "RESTART" which one of the 4 possible variants (5, 10, 15, 20 ATTEMPTS) - the amount of codes after which adapter will perform restart procedure.
3. Adjust the angle of the pressing arm to POWER button on the phone - to do so, in the submenu select the ANGLE and set the appropriate value (arm should be perpendicular to the Power button on the phone), then you should remove the arm by 5 degrees (5 DEG) button down and confirm the setting by pressing the SET button. For most mobile setting will be between 80 to 90 degrees, ie. from 80 DEG to 90 DEG in Menu.
4. Install the phone in the holder - check if the height of the POWER button on the phone is in the middle of the arm, if not, make adjustment by moving the phone up and down in the holder.
5. Attach the handle with your phone to the platform so that the POWER button phone was located approximately 1 mm from the shoulder. Click the SET button in the menu ANGLE and press the directional up button (one click is a movement of 5 degrees) to check if the arm clicked the POWER button on the phone. If the phone is out of range of the arm move holder closer.
6. Connect XPIN Clip with your phone using Charging cable (black one from standard set). Don't use 4in1 XPIN cable for reSTART adapter since it can cause problems.
7. Place the light sensor on the phone and make other settings (SENSOR, TIMING, RANGE, etc.)
8. Press the START button to begin the procedure attack on the PIN code.
Watch FAQ of using reSTART adapter:
Complete contains:
- ReSTART Adapter
- holder
- IDC 26 communication cable
Features:
- Allows an attack on the PIN code preventing "jam" TouchWiz interface
- Shortens the time of the attack on some versions of Android 6.x.x
Specification
Adapter connected to XPIN Clip
Instruction:
1. Connect the reSTART adapter with IDC 26 cable to XPIN clip, then connect the 5V power supply to the mini USB (use charger with min. 1A), connect the power supply to XPIN Clip (USB B).
2. Select Android PIN and then the submenu "RESTART" which one of the 4 possible variants (5, 10, 15, 20 ATTEMPTS) - the amount of codes after which adapter will perform restart procedure.
3. Adjust the angle of the pressing arm to POWER button on the phone - to do so, in the submenu select the ANGLE and set the appropriate value (arm should be perpendicular to the Power button on the phone), then you should remove the arm by 5 degrees (5 DEG) button down and confirm the setting by pressing the SET button. For most mobile setting will be between 80 to 90 degrees, ie. from 80 DEG to 90 DEG in Menu.
4. Install the phone in the holder - check if the height of the POWER button on the phone is in the middle of the arm, if not, make adjustment by moving the phone up and down in the holder.
5. Attach the handle with your phone to the platform so that the POWER button phone was located approximately 1 mm from the shoulder. Click the SET button in the menu ANGLE and press the directional up button (one click is a movement of 5 degrees) to check if the arm clicked the POWER button on the phone. If the phone is out of range of the arm move holder closer.
6. Connect XPIN Clip with your phone using Charging cable (black one from standard set). Don't use 4in1 XPIN cable for reSTART adapter since it can cause problems.
7. Place the light sensor on the phone and make other settings (SENSOR, TIMING, RANGE, etc.)
8. Press the START button to begin the procedure attack on the PIN code.
Watch FAQ of using reSTART adapter:
Complete contains:
- ReSTART Adapter
- holder
- IDC 26 communication cable
|
||
NEGOTIATE PRICE
Additional information about this product:
Information concerning features of this tool :Developer provides support only for those phones which are on the list of supported. Not all servicing features can be applied to some supported models, due to difference of hardware / software versions. Complete list of supported models you can find on the official product page, or on the GSM forum (GSMHosting).
Information concerning technical requiments :
The correct use of the purchased goods is required to have a stable internet connection with min . capacity of 1024 kb / s ( download) and 512 kb / s ( upload) . Before you attempt to make software update on the device or want to activate/use service, make sure that you have a sufficient link parameters .
Information concerning the interoperability of digital content:
For using a software or a piece of software that the manufacturer supplies with purchased hardware, in some cases it’s required that you disable your Firewall ( in software or router) and antivirus software. Leaving it enabled can occurs inproper operation of software / services and you will get communications errors like “Error 10060”.
Information concerning hardware requiments:
For proper working with this device producer suggest PC computer with 32-bit Windows XP operating system. We don't guarantee that software/device will work or any other system - especially 64-bit systems, iMac, Linux.
Information concerning IMEI change:
We want to inform that IMEI change option in softwares are intended to use only to repair broken IMEI and retrieve it to original state. It's prohibitted to use this function to change IMEI to diffrent that original. Multi-COM don't answer to any questions related with operation on IMEI number - if you require help in this metter please contact with software/device producer directly. We don't take any responsibility to use this function.
If you are interested in
reSTART Adapter for XPIN Clip
you will probably want to take a look at following products:
Dedicated equipments for this adapter:
+
|
XPIN Clip with cables set
more
|
Price:
349.00 EUR w/o VAT |
See also
+
|
Flat Tape for XPIN Clip Pattern Adapter
more
|
Price:
3.00 EUR w/o VAT |
+
|
TRC sensor light cable for XPIN Clip
more
|
Price:
7.00 EUR w/o VAT |
+
|
Pattern Adapter for XPIN Clip
more
|
Price:
60.00 EUR w/o VAT |
+
|
XPIN Charging cable for Android
more
|
Price:
7.00 EUR w/o VAT |
+
|
XPIN upgrade firmware USB cable - A-A
more
|
Price:
3.49 EUR w/o VAT |
+
|
OS800 Adapter for XPIN Clip (iOS 8.0 - 8.1)
more
|
Price:
299.00 EUR w/o VAT |
You might also be interested in:
+
|
XPIN Clip full set (CASE)
more
|
Price:
899.00 EUR w/o VAT |
|
+
|
XPIN Clip with cables set
more
|
Price:
349.00 EUR w/o VAT |
+
|
HXC Dongle & HXC ProTool
more
|
Price:
59.00 EUR w/o VAT |
+
|
UFS3 UI Tornado + HWK by GPG
more
|
Price:
69.00 EUR w/o VAT |
+
|
Octoplus Box + LG activation
more
|
Price:
179.00 EUR w/o VAT |
+
|
DC-Unlocker USB key LITE
more
|
Price:
70.00 EUR w/o VAT |
+
|
Infinity Plus 2in1 PinFinder + Infinity Dongle-Box
more
|
Price:
159.00 EUR w/o VAT |
+
|
GC PRO Key
more
|
Price:
149.00 EUR w/o VAT |
This product was bought most often with:
+
|
9in1 Dismantle Car Audio Pry Open Tool Set
more
|
Price:
15.00 EUR w/o VAT |
+
|
Medusa Pro Box (JTAG i EMMC)
more
|
Price:
159.00 EUR w/o VAT |
+
|
Spatula for spreading flux 5cm (XT-82S)
more
|
Price:
3.50 EUR w/o VAT |
|
+
|
OS800 Adapter for XPIN Clip (iOS 8.0 - 8.1)
more
|
Price:
299.00 EUR w/o VAT |
|
+
|
XPIN upgrade firmware USB cable - A-A
more
|
Price:
3.49 EUR w/o VAT |
+
|
USB Analyzer / VCC Adapter
more
|
Price:
25.00 EUR w/o VAT |
+
|
FuriousGold USB KEY All In One
more
|
Price:
129.00 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.
