4,8 RATING:
Purchase satisfaction
94,7%
Customer service
94,0%
Shop offer
92,7%

Cart

0 products
Main page > GSM products > JTAG / EMMC / UFS Adapters > EMMC / UFS cables and adapters > Adapter EMMC for Riff BOX (RC1000)

Adapter EMMC for Riff BOX (RC1000)

5 (3)
Adapter EMMC for Riff BOX (RC1000)
Price: 25,00 EUR w/o VAT

Quantity

ID: 17319

Product weight: 0.10 kg

Add to store products

Ask for product

Adapter EMMC for Riff BOX - RC1000 allows a very simple repair phones with blocked JTAG access (GT-i9300 / N7100 / N719 / N7102, etc.), repair phones with damaged JTAG points/pads (access to ROM2 by EMMC) or read/write EMMC applicable for the data recovery/analysis. Using the adapter you can perform format EMMC or low-format (in case of damage EMMC), CMD42 Lock/Unlock/Pasword reset or Samsung eMMC Factory Format. Our adapter allows you to connect in ISP mode (directly onto your phone without removing the EMMC) or Direct (by removing the BGA soldering and the corresponding memory fields or using adapter).

Advantages of the use of an adapter RC1000:
- Full control over the VCC / VCCQ by connection of external power from USB
- The ability to turn ON/OFF Pull-UP CMD and DATA (Dat0) to increase signal levels and improve stability
- Lack of communication problems by applying the same path length for the transmission signals
- The ability to connect the IDC 10 pin connector
- allows use BGA adapters used in CHIP-Off for Direct Mode



Features:
– eMMC/SD reading info, browsing through OCR, CID, CSD (and EXT_CSD for eMMC only) registers’ fields, edit separate fields and writting back to card, reading/writting eMMC card’s MCU’s internal firmware, etc
– eMMC Firmware Update option
– eMMC Firmware Reading option
– CMD42 Lock/Unlock functionality for eMMC - user can set/change/remove password to protect/unprotect (lock/unclock) the User Area Partition
– User Area Partition Forced Erase to erase Locked User Area Partition and to reset Device lock/unlock state and password (CMD42’s consequences)
– Samsung Factory Erase which erases and re-formats the Samsung eMMC chips.


Output signals on the adapter:
- GND
- CMD (ON/OFF DipSwitch to enable/disable pullup signal - 100 ohm)
- CLK
- Dat0 (ON/OFF DipSwitch to enable/disable pullup signal - 100 ohm)
- VCC (voltage regulation using two modes - 2.8V / 3.3V)
- VCCQ (regulation voltage range in three modes - 1.8V / 2.8V / 3.3V)

Pinout GPG eMMC adapter


Pinout RC1000


Note: Each of the signals is described on the PCB

Photo adapter:



Movie showing the adapter in connection stage:


Set includes
- Adapter RC1000 for Riff BOX
Product weight: 0.10 kg.
Country:
Courier:
Delivery time: 14-28 working days from shiping date
Shipping cost: 9.75 EUR

NEGOTIATE PRICE

PDF
If you are interested in Adapter EMMC for Riff BOX (RC1000) you will probably want to take a look at following products:

Other products from same category

Flat tape 20 pin for JRT/ORT/RIFF + Flat tape 20 pin for JRT/ORT/RIFF more
Price:
3.50 EUR w/o VAT
Power supply cable for Riff JTAG + Power supply cable for Riff JTAG more
Price:
3.00 EUR w/o VAT
PROBE cable for Riff JTAG Box + PROBE cable for Riff JTAG Box more
Price:
8.00 EUR w/o VAT
PKG activation/licence for Riff BOX + PKG activation/licence for Riff BOX more
Price:
29.00 EUR w/o VAT

Dedicated equipments for this adapter:

RIFF Box JTAG/EMMC ORIGINAL + RIFF Box JTAG/EMMC ORIGINAL more
Price:
119.00 EUR w/o VAT

Dedicated logs/credits for this device

Credits/ EMMC activation for Riff BOX + Credits/ EMMC activation for Riff BOX more
Price:
31.83 EUR w/o VAT

See also

Adapter eMMC/JTAG for Riff BOX 2 - RC2000 + Adapter eMMC/JTAG for Riff BOX 2 - RC2000 more
Price:
10.00 EUR w/o VAT

You might also be interested in:

ICFRIEND ISP eMMC/UFS Adapter + ICFRIEND ISP eMMC/UFS Adapter more
Price:
8.00 EUR w/o VAT
Adapter eMMC/JTAG for Riff BOX 2 - RC2000 + Adapter eMMC/JTAG for Riff BOX 2 - RC2000 more
Price:
10.00 EUR w/o VAT
SD/MicroSD reader for a Z3x JTAG Plus - 1bit + SD/MicroSD reader for a Z3x JTAG Plus - 1bit more
Price:
24.00 EUR w/o VAT
EMMC adapter for Easy Z3x JTAG Box + EMMC adapter for Easy Z3x JTAG Box more
Price:
12.00 EUR w/o VAT
Adapter eMMC/JTAG dla Riff Box 2 - RC3000 + Adapter eMMC/JTAG dla Riff Box 2 - RC3000 more
Price:
18.00 EUR w/o VAT
Adapter for ATF 20PIN EMMC - RJ45 + Adapter for ATF 20PIN EMMC - RJ45 more
Price:
4.00 EUR w/o VAT
ISP S2 adapter for MiPi Tester UFS/eMMC + ISP S2 adapter for MiPi Tester UFS/eMMC more
Price:
11.00 EUR w/o VAT
SD-EMMC Plus Adapter - Model SE-P1 + SD-EMMC Plus Adapter - Model SE-P1 more
Price:
17.00 EUR w/o VAT

This product was bought most often with:

Power supply cable for Riff JTAG + Power supply cable for Riff JTAG more
Price:
3.00 EUR w/o VAT
Adapter eMMC/JTAG for Riff BOX 2 - RC2000 + Adapter eMMC/JTAG for Riff BOX 2 - RC2000 more
Price:
10.00 EUR w/o VAT
PROBE cable for Riff JTAG Box + PROBE cable for Riff JTAG Box more
Price:
8.00 EUR w/o VAT
ATF TP Finder + ATF TP Finder more
Price:
19.00 EUR w/o VAT
Universal JTAG/eMMC/FBUS JE-02 adapter + Universal JTAG/eMMC/FBUS JE-02 adapter more
Price:
20.00 EUR w/o VAT
RIFF Box 2 - JTAG/EMMC/I2C ORIGINAL + RIFF Box 2 - JTAG/EMMC/I2C ORIGINAL more
Price:
159.00 EUR w/o VAT
Adapter EMMC ATF V2 4in1 + Adapter EMMC ATF V2 4in1 more
Price:
25.00 EUR w/o VAT

Note

1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.

2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.

3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.

Reviews

The listed opinions/reviews come only from customers who have purchased a given product/service in our online store. See what they think about a given product or service

ok
Jakosc, wykonanie, termin realizacji wzorcowy. Polecam