 |
Radio Code cables Adapters
Browse
List
Gallery
15045 |
Adapter for Delco CDR 500/2005 for Martech BOX III Adapter for Delco CDR 500/2005 for Martech BOX III is used to reading original code via K-Line protocol (no need to open radio, decoding goes via backside connector), reset counter of tries while reading code, code calculation from serial number (SN Calculator) |
 |
|
16680 |
Ford MC CAN cable for Martech BOX III Ford MC CAN cable for Martech BOX III is used to read the code from the Ford radio by CAN bus using Martech BOX III without soldering and stripping the radio. |
|
|
|
8393 |
MC68HC Adapter Set allows to easily access MC68HC processor memory without soldering to it. You can to read, write, verify EEPROM processor memory. Designed and produced especially for Martech Clip device (Radio Code Full pack) but can be used also to any other programmer that support MC68HC (signals are describe on PCB) |
|
|
|
8380 |
MC68HC(7)05 Adapter alllows to easily access MC68HC(7)05 processor memory without soldering to it. You can you it to read, write, verifiy EEPROM processor memory. Designed and produced especially for Martech Clip device (Radio Code Full pack) but can be used also to any other programmer that support MC68HC (signals are describe on PCB) |
|
|
|
8381 |
MC68HC(7)11 Adapter alllows to easily access MC68HC(7)11 processor memory without soldering to it. You can you it to read, write, verifiy EEPROM processor memory. Designed and produced especially for Martech Clip device (Radio Code Full pack) but can be used also to any other programmer that support MC68HC (signals are describe on PCB) |
|
|
|
8382 |
MC68HC11F1 Adapter alllows to easily access MC68HC11F1 processor memory without soldering to it. You can you it to read, write, verifiy EEPROM processor memory. Designed and produced especially for Martech Clip device (Radio Code Full pack) but can be used also to any other programmer that support MC68HC (signals are describe on PCB) |
|
|
|
8383 |
MC68HC11KA4 Adapter alllows to easily access MC68HC11KA4 processor memory without soldering to it. You can you it to read, write, verifiy EEPROM processor memory. Designed and produced especially for Martech Clip device (Radio Code Full pack) but can be used also to any other programmer that support MC68HC (signals are describe on PCB) |
|
|
|
8389 |
MC68HC11L6 Adapter alllows to easily access MC68HC11L6 processor memory without soldering to it. You can you it to read, write, verifiy EEPROM processor memory. Designed and produced especially for Martech Clip device (Radio Code Full pack) but can be used also to any other programmer that support MC68HC (signals are describe on PCB) |
|
|
|
14728 |
RNS 300 connection interface BOX III RNS 300 connection interface BOX III connection interface between RNS 300 navigation and Martech BOX III. Useful for RNS 300 / Lowline Decoder. |
|
|
|
7187 |
Adapter K-line ISO for Martech Adapter K-line ISO for Martech it's special adapter that allows you to communicate with devices based on K-line protocol. Our product are final one - inclusing ISO connector for CDR500 for powering your radio as well as ISO Kline for diagnose. Due using RJ45 adapter socket it's possible to purchae additional cables in future when will be available as for CDR2005 or OBD2 |
|
|
|
15039 |
BP-BUS cable for Martech BOX III BP-BUS cable for Martech BOX III is used for resetting cancheck over BP-BUS. By using this cable you can very fast and easy without need of soldering make such operations as Cancheck Off, Cancheck On, Reset Counter, Write , Code off, Code on, Read Code... |
|
|
|
7833 |
Cable Opel CDR500 for K-Line Martech Cable Opel CDR500 for K-Line Martech it's additional cable for produced by us Martech KLine adapter with original opel CDR500 connector instead of ISO one. |
|
|
|
16823 |
Cable Opel K-Line + LCD Emulator for Martech BOX III Cable Opel K-Line + LCD Emulator for Martech BOX III is used to read the code on line K of radio Opel and emulation of the LCD. The whole is carried out without soldering and stripping the radio - use the diagnostic connector using Martech BOX III. |
|
|
|
15044 |
Diagnostic adapter DB25 for Martech Box III Diagnostic adapter DB25 for Martech Box III is used for autotest Box III. |
|
|
|
6504 |
Martech I2C SOIC for RCD it's special adapter for all users of RCD/SQM application to read out memory, codes as also write them back using Martech Box 2+/Clip/Lite. Without need to desolder memory in some models you can read out memory. You don't need ofcourse anymore additional programmer. |
|
|
|
14729 |
Martech RNS 315 Expander additional module for Clip that expands technical capabilities of the device for servicing such radios like RCD 310 / 510, RNS 315, RCD 500, Navi Dresden and Gamma 3. Special RNS activation it's required for use expander. |
|
|
|
14726 |
Programmer adapter Martech BOX III |
|
|
|
16832 |
Renault Tuner List LCD Emulator Cable for Martech BOX III Renault Tuner List LCD Emulator Cable for Martech BOX III allows the emulation of the LCD Renault car radio Tuner list on your desktop PC via Martech BOX III. |
|
|
|
8789 |
RNS 300 Cable for Martech Clip RNS 300 Cable for Martech Clip it's special cable to use with RNS 300 series for directo connection with Martech Clip and radio. |
|
|
|
8791 |
RNS 310 Cable for Martech Clip RNS 310 Cable for Martech Clip it's special cable to use with RNS 310 series for directo connection with Martech Clip and radio. |
|
|
|
