|
Main page > GSM products > JTAG / EMMC / UFS Adapters > JTAG cables and adapters > S-Boot Repair cable for Samsung
|
 |
S-Boot Repair cable for Samsung
S-Boot Repair cable for Samsung to repair the boot on Samsung i9500, i9300, i9308, i939d, m440s, i317, T889, E210k, E210L, E210s, N7100, N7108, N719, N7102 very easily without soldering. No disassembly is required except for a couple of models whereby you just need to remove the screen before doing the work.
Supported Models:
- i9500 (Samsung Galaxy S4)
- i9300 (Samsung Galaxy S3)
- i9308 (Samsung Galaxy S3)
- i939d (Samsung Galaxy S3)
- m440s (Samsung Galaxy S3)
- i317 (Samsung Galaxy Note II)
- T889 (Samsung Galaxy Note II)
- E210k (Samsung Galaxy S3)
- E210L (Samsung Galaxy S3)
- E210s (Samsung Galaxy S3)
- N7100 (Samsung Galaxy Note II)
- N7108 (Samsung Galaxy Note II)
- N719 (Samsung Galaxy Note 2 CDMA)
- N7102 (Samsung Galaxy Note 2 WCDMA)
Samsung i9300 dead boot repair tutorial with GPG S-Boot Clip:
Power off phone.
Insert SD card connector from S-Boot cable into i9300
Connect power preferrably with regulated power supply or battery power supply, recommend to use of regulated power supply, because it can observe the change of electric current, when everything is ready.
Insert 19000 download clip.
Now wait, do not cut off power supply in the middle otherwise it may not be repaired at all.
Generally after 2-5minutes, it will enter download mode.
If more than 5 minutes it has not entered download mode, then this usually means phone has flash ic problem or other hardware problems, please check the other reasons.
In the repair process, power current will jump every few seconds, which is telling you it is writeing data from SD to mobile phone.
Do not cut off power, otherwise it may never be able to repair again.
Samsung N7100 dead boot repair tutorial with GPG S-Boot Clip:
Remove the screen from the N7100 (if not removed, it will burn after repair)
Connect regulated power supply to N7100 pcb battery terminals
Insert SD card connector from S-Boot cable into N7100
Insert i9000 download clip
Now wait, do not cut off power supply in the middle otherwise it may not be repaired at all.
If the flash is not completely broken, it will be repaired after 5minutes, and will enter download mode.
Plug the i9000 download clip and run flashing platform.
See if it recognizes the driver and port, if it does, then you can load file and flash, but remember to leave screen off until phone flashing is completed, or the screen will burn.
Samsung i9500 dead boot repair tutorial with GPG S-Boot Clip:
Remove the screen from the i9500 (if not removed, it will burn after repair)
Connect regulated power supply to i9500 pcb battery terminals
Insert SD card connector from S-Boot cable into i9500
Insert i9000 download clip
Now wait, do not cut off power supply in the middle otherwise it may not be repaired at all.
If the flash is not completely broken, it will be repaired after 5minutes, and will enter download mode.
Plug the i9000 download clip and run flashing platform.
See if it recognizes the driver and port, if it does, then you can load file and flash, but remember to leave screen off until phone flashing is completed, or the screen will burn.
After flashing phone is in good state, just like you have changed the flash ic
If phone hangs after enter mode however, it means flash ic is totally damaged or other hardware problems and cannot be fixed.
Package contents:
1 x S-Boot Repair Clip
Supported Models:
- i9500 (Samsung Galaxy S4)
- i9300 (Samsung Galaxy S3)
- i9308 (Samsung Galaxy S3)
- i939d (Samsung Galaxy S3)
- m440s (Samsung Galaxy S3)
- i317 (Samsung Galaxy Note II)
- T889 (Samsung Galaxy Note II)
- E210k (Samsung Galaxy S3)
- E210L (Samsung Galaxy S3)
- E210s (Samsung Galaxy S3)
- N7100 (Samsung Galaxy Note II)
- N7108 (Samsung Galaxy Note II)
- N719 (Samsung Galaxy Note 2 CDMA)
- N7102 (Samsung Galaxy Note 2 WCDMA)
Samsung i9300 dead boot repair tutorial with GPG S-Boot Clip:
Power off phone.
Insert SD card connector from S-Boot cable into i9300
Connect power preferrably with regulated power supply or battery power supply, recommend to use of regulated power supply, because it can observe the change of electric current, when everything is ready.
Insert 19000 download clip.
Now wait, do not cut off power supply in the middle otherwise it may not be repaired at all.
Generally after 2-5minutes, it will enter download mode.
If more than 5 minutes it has not entered download mode, then this usually means phone has flash ic problem or other hardware problems, please check the other reasons.
In the repair process, power current will jump every few seconds, which is telling you it is writeing data from SD to mobile phone.
Do not cut off power, otherwise it may never be able to repair again.
Samsung N7100 dead boot repair tutorial with GPG S-Boot Clip:
Remove the screen from the N7100 (if not removed, it will burn after repair)
Connect regulated power supply to N7100 pcb battery terminals
Insert SD card connector from S-Boot cable into N7100
Insert i9000 download clip
Now wait, do not cut off power supply in the middle otherwise it may not be repaired at all.
If the flash is not completely broken, it will be repaired after 5minutes, and will enter download mode.
Plug the i9000 download clip and run flashing platform.
See if it recognizes the driver and port, if it does, then you can load file and flash, but remember to leave screen off until phone flashing is completed, or the screen will burn.
Samsung i9500 dead boot repair tutorial with GPG S-Boot Clip:
Remove the screen from the i9500 (if not removed, it will burn after repair)
Connect regulated power supply to i9500 pcb battery terminals
Insert SD card connector from S-Boot cable into i9500
Insert i9000 download clip
Now wait, do not cut off power supply in the middle otherwise it may not be repaired at all.
If the flash is not completely broken, it will be repaired after 5minutes, and will enter download mode.
Plug the i9000 download clip and run flashing platform.
See if it recognizes the driver and port, if it does, then you can load file and flash, but remember to leave screen off until phone flashing is completed, or the screen will burn.
After flashing phone is in good state, just like you have changed the flash ic
If phone hangs after enter mode however, it means flash ic is totally damaged or other hardware problems and cannot be fixed.
Package contents:
1 x S-Boot Repair Clip
|
||
NEGOTIATE PRICE
If you are interested in
S-Boot Repair cable for Samsung
you will probably want to take a look at following products:
See also
+
|
RIFF Box JTAG/EMMC ORIGINAL
more
|
Price:
119.00 EUR w/o VAT |
+
|
Clip for Samsung Download Mode
more
|
Price:
2.99 EUR w/o VAT |
+
|
Magic cable for Chineese Android Boot SPD
more
|
Price:
7.00 EUR w/o VAT |
+
|
EMMC adapter for Easy Z3x JTAG Box
more
|
Price:
12.00 EUR w/o VAT |
This product was bought most often with:
+
|
JTAG for Samsung i9505/M919/i337 (Galaxy S4)
more
|
Price:
10.00 EUR w/o VAT |
|
+
|
EMMC adapter for Easy Z3x JTAG Box
more
|
Price:
12.00 EUR w/o VAT |
+
|
MBC Multi Boot Cable for Z3x/Octopus/UST
more
|
Price:
8.00 EUR w/o VAT |
|
+
|
Clip for Samsung Download Mode
more
|
Price:
2.99 EUR w/o VAT |
+
|
LCD Opener
more
|
Price:
4.00 EUR w/o VAT |
+
|
JTAG for Samsung i9100/i9100P (Galaxy S2)
more
|
Price:
11.00 EUR w/o VAT |
+
|
JTAG for Samsung I747/I747M/T999/T999V (Galaxy S3)/I9190/I9195 (S4 Mini)
more
|
Price:
11.00 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.
