|
Main page > Repair Equipment > Soldering Equipment > BGA Rework stations > Tornado Infra held station
|
 |
Tornado Infra held station
Tornado Infra held station it's first hand held infra rework station. Here is an honest attempt to give infra rework at reasonable price without any degradation in quality. Our product has been built using one of the best infrared techniques an best to use with lead-free PCB's.
Most common questions:
Q: What more can it do than a hot air?
A: First since 2006 June all PCBs made all over the world must be lead free PCBs. The melting temperature for lead free solder is 225 °C. Also if you have a PCB with lead free solder wire and if you try using hot air to repair it the PCB tracks can go bad. So there is no other choice but to use INFRA heating station
Specification:
Pre Heater:
This infrared heating element contains the CE marking.
The CE marking indicates conformity with the relevant European safety directive(s).
Heating element specifications:
Iron-chrome aluminum resistance wire
Heater Voltage: 230 Volts standard.
Electrical Power Loading: 6.8 W/cm2 (43.5W/inch)
Useful wavelength range: 2 to 10 Microns.
Average Operating Life: 5,000 - 10,000 Hours.
Mean Maximum Surface Temperature: 685°C
Approximate Time Until Top Temperature: 8 minutes
The heat up curves for ceramic heater are as shown below
Package contains:
- Infra Tornado station
- mulimter/termometr for measuring temp from Infra
- flux
We offer 6 months of warranty for this product
Most common questions:
Q: What more can it do than a hot air?
A: First since 2006 June all PCBs made all over the world must be lead free PCBs. The melting temperature for lead free solder is 225 °C. Also if you have a PCB with lead free solder wire and if you try using hot air to repair it the PCB tracks can go bad. So there is no other choice but to use INFRA heating station
Specification:
Pre Heater:
Heating element specifications:
The heat up curves for ceramic heater are as shown below
Package contains:
- Infra Tornado station
- mulimter/termometr for measuring temp from Infra
- flux
wARRANTY
We offer 6 months of warranty for this product
|
||
NEGOTIATE PRICE
If you are interested in
Tornado Infra held station
you will probably want to take a look at following products:
See also
+
|
Protection tape JOVY-R0 50m
more
|
Price:
45.00 EUR w/o VAT |
+
|
Jovy System BGA RE-7500
more
|
Price:
1129.00 EUR w/o VAT |
+
|
Infra held stand
more
|
Price:
89.00 EUR w/o VAT |
+
|
Tornado Infra PRO held station
more
|
Price:
319.00 EUR w/o VAT |
+
|
Samsung C160 USB cable
more
|
Price:
10.00 EUR w/o VAT |
+
|
Soldering Smoke Absorber CT629 ESD
more
|
Price:
99.00 EUR w/o VAT |
+
|
Infra station held unit
more
|
Price:
119.00 EUR w/o VAT |
+
|
Heat element for Tornado Infra
more
|
Price:
79.00 EUR w/o VAT |
This product was bought most often with:
+
|
Screen protection film-R (55mm)
more
|
Price:
8.00 EUR w/o VAT |
+
|
Sagem TP MY-700x cable with Switch
more
|
Price:
3.80 EUR w/o VAT |
+
|
Microscope SZM7045-STL1
more
|
Price:
552.00 EUR w/o VAT |
|
+
|
Infra held stand
more
|
Price:
89.00 EUR w/o VAT |
+
|
Cable for JIG adapters BB5 Box
more
|
Price:
15.00 EUR w/o VAT |
+
|
Rework "no clean" - soldering help pen
more
|
Price:
10.00 EUR w/o VAT |
+
|
Cable for Nokia N95 8GB RJ48 MT-BOX (10 pin)/GTI
more
|
Price:
5.50 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.
