MFC Dongle

MFC Dongle allows you to get user password on iPhone 4,4s, 5, 5s, 5c (V7.1.1/ V7.1.2) and HTC/Samsung Android mobile phones (V4.3+). MFC Dongle does not require resetting your device which entails deleting data and reverts the device to factory settings. MFC Dongle keeps your device's data and allows to get the passcode easily.

A screen lock passcode is a good security measure. If you forget this passcode, One last-resort solution to this is resetting your device which deletes all your data and reverts the device to factory settings. From right now MFC Dongle with a special solution will never lost or distroy device Data which can automatically get the passcode easily.

ATENTION: IF IPHONE HAVE SET OPTION ERASE DATA AFTER 10 FAILED PASSCODE ATTEMPTS, THEN ALL DATA WILL BE DELETED!







Supported models:

• Apple
  iPhone 4
  iPhone 4s
  iPhone 5
  iPhone 5s
  iPhone 5c
  iPad
  Mac Book


• Samsung


• Android - version: 4.3+


• HTC


• Android - version: 4.3+
  
  
  
  
  
  
  
  About Samsung Android 4.3+ tested on Samsung Galaxy S5
  
  Request for Version 1.0.3 or newer
  This update will try 5 codes then 30 seconds of waiting
  About 40 seconds / 5 codes (22 hours to try all codes) in some mobile phones the delay between codes will increase up to 10 seconds with more wrong codes so delay between codes must be around 10000ms(10seconds) so the waiting time will be 44 hours not 22. You must adjust the delay accordingly.
  How to:
  Connect the light sensor to the darkest place on the screen
  Insert MFC dongle
  Wait until unlock is ok (usually the MFC dongle will stop at that point)
  Press read in MFC dongle update software and connect MFC dongle to computer to read the unlock codes
  
  About HTC Android 4.3+ tested on HTC One
  
  It will try 5 codes then wait 30 seconds while keeping the screen on ,about 40 seconds for 5 codes (22 hours for all 4 digits possible codes)
  How to:
  Unlock phone and go to the phone lock screen and insert MFC Dongle, Future update ... add code detection using light sensor
  
  About Apple iPhone Version iOS 7.1.1 ?
  
  Using this method unlock time si maximum 13.5 hours for all 9999 possible codes (1 codes each 5 seconds)
  How To:
  update MFC dongle using Update 1 - iOS 7.1.1
  write the appropriate settings using the software (the delay in milliseconds is 5000 for iOS 7.1.1) 5 seconds / code
  connect the light sensor to the phone in a blank area (blue)
  put a sim card inside the phone
  call the sim card number
  answer on the iPhone then go to Contacts
  when the lock code is required insert MFC Dongle
  if you get the message accessory not supported just press ok. Another message might also appear after first minute so you need to press ok to that too otherwise you might miss some codes during the time the message is displayed.
  when we reach the correct code the screen will change to Contacts screen thus triggering the light sensor and the process will stop
  you can now connect the MFC dongle to computer and click read button.
  
  About Apple iPhone Version iOS 7.1.2 Auto Method ?
  
  This will be request for Version 1.0.3 or new version.
  This update will automatically try to find the code and require no user intervention.
  Just connect MFC dongle to phone and unlocking will start.
  The light sensor must be connected in such a way that after unlocking is done the light sensor will detect more like that initially detected. Usually this can be achieved if the light sensor is placed in the left top corner, where the message icon will be displayed after unlock.
  The delay must be at least 4500 for correct function.
  
  About Apple iPhone Version iOS 7.1.2 manual Method (phone is disabled)?
  
  This update will help you unlock your phone code even if the phone is disabled after too many retries.
  The default delay for this update is about 4300 ms (4.3 seconds).
  Update your MFC dongle using this update and connect the light sensor on the top right side of the iPhone screen.
  Go to the phone disable screen and connect MFC dongle to phone and wait 5 seconds.
  Swipe with your finger to go to Emergency calling.
  The MFC dongle will automatically detect the swipe and try the next available code.
  Then the phone will automatically come back to the phone lock screen.
  To continue swipe again to the emergency screen and so on until your phone is unlocked.
  
  Downloading and installing drivers.
  
  1. Download and unzip MicrosoftRedistributables.zip to the mfc-dongle folder you made
  go in the MicrosoftRedistributables folder and install vcredist_x86.exe and vcredist_x64.exe
  
  2. Download and unzip DongleDrivers.zip to the mfc-dongle folder you made
  go in the DongleDrivers foldr and run the InstallDriver.exe
  
  To install the dongle update driver you need to connect MFC dongle to computer in BOOT MODE.
  Use the red cable to bridge the 2 points together P0 and GND (see images below) and once done, connect the dongle to your PC
  Once drivers are installed you can now disconnect the dongle
  
  
  
  Set contains:
  - MFC Dongle with USB OTG Cable - 1 pc.
  - Sensor Adaptor - 1 pc.
  - OTG Cable (for Samsung, HTC and iPhone) - 3 pcs.
  - Data Cable - 3 pcs.

Product placed on the market in the EU before December 13, 2024: YES

Safety Warnings and Usage Guidelines

Based on the requirements of Regulation (EU) 2023/988 on General Product Safety (GPSR), we present a list of safety warnings. The aim is to protect users from potential hazards resulting from improper use of products/devices.

1. General Safety Measures

* Use the device only in accordance with its intended purpose and the manufacturer's instructions.
* Before first use, read the user manual carefully.

Hazards for children:
* Keep the product/device out of reach of children. Children are unable to assess existing risks.

2. Mechanical Hazards

* Check that all components are properly assembled before operating the device.
* Avoid using tools that may damage the product or contribute to its damage. Do not modify the product: do not open/disassemble it!

3. Electrical Hazards
* Connect only to a socket with the appropriate voltage, in accordance with the manufacturer’s requirements.
* Improper handling of products powered by mains voltage may result in fatal electric shock! If the product and/or the connection cable are damaged, do not touch them; there is a risk of fatal electric shock! Never use the device if the power cord is damaged, frayed, or cut. Avoid touching the power cord or plug with wet hands.
* Product with a separate power supply: before connecting the device to a plug-in or external power supply, ensure that the voltage, polarity (plus/+ and minus/-), and plug dimensions (e.g., inner/outer diameter) match the device.
* Product with a mains plug: the power outlet used for connection must be located near the product and easily accessible. Always unplug the power cord by pulling the plug, not the cable.
* Product with a power cord: the power cable must not be pinched, bent, or damaged by sharp edges. Do not place any objects on the power cord or step on it. The cable should always be arranged carefully to prevent tripping.
* Product intended for soldering: use only appropriate electronic solder and an electronic soldering iron. The soldering process should be performed quickly to avoid overheating and possible damage to the product.

4. Usage Precautions

* Place the product on a stable, flat surface to prevent it from tipping over.
* Always maintain sufficient space around the device (as recommended by the manufacturer) to ensure proper ventilation.
* The operation of certain products (e.g., machines or tools) requires the use of personal protective equipment to minimize health or other risks. This includes, for example, suitable hearing protection, an appropriate respirator/dust mask, or safety goggles, as well as proper gloves, safety footwear, and clothing.

5. Maintenance and Cleaning
* Before performing maintenance or cleaning, read the product’s user manual.
* Improper cleaning agents may not only damage the product but also cause other hazards — follow the manufacturer’s guidelines.

6. User Warnings
* Elderly persons or individuals with limited mobility should exercise particular caution when operating the product and, if necessary, seek assistance from another person.
* If the device operates abnormally (e.g., emits smoke, overheats, or produces unusual sounds), immediately switch it off, disconnect it from power, and contact authorized service.
* Store the product in a dry and cool place to prevent mechanical and electrical damage.

7. Disposal
* All electrical and electronic equipment placed on the European market must be properly disposed of. This means that, at the end of its service life, the device must be disposed of separately from unsorted household waste.

8. Importance of Following the Warnings
Following the above warnings minimizes the risk of personal injury, device malfunction, and material losses. Ignoring these recommendations may lead to serious health and material hazards. Protect yourself and your loved ones by following the indicated safety measures. Detailed warnings or product safety information are available in the user manual supplied with the product or in PDF format on the manufacturer’s/supplier’s website.