 |
iPower Adaptor for MFC Dongle
This product cannot be purchased using Paypal due to their restriction on computer surveillance products. Other payment methods available.
iPower Adaptor for MFC Dongle is needed if you need to unlock Apple iPhone iOS 8.0.x - 8.1 devices. This update will try one code after each phone will restart. The restart is performed automatically using the iPower adaptor by MFC Box Team. Please read full details from instruction and check support forum before you do unlock your device. The reboot time depends on the phone (newer models reboot faster). Usually is about 40 seconds(E.g.iPhone 5). Maximum time is 4.6 days in this way from 0 to 9999(111 hours).
Additional information:
In case your phone displays Phone disabled 15 minutes remaining, you will have to wait at least 15 minutes before starting to unlock. Codes sent to the phone during this time will always be invalid even if the code is correct.
If phone displays 23 million minutes remaining it means the phone has lost correct time setting after taken out the battery. You can insert an active simcard into the phone to get the correct time and date then revert back to the normal 1,2,15,60 minutes waiting message etc. In our test we were able to use MFC even without simcard as the phone will revert back to the normal waiting time after the first reboot. But you need to take into consideration the fact that if the phone displays wait for 60 minutes then have to wait 60 minutes until you can really start to unlock procedure.
How to use:
1. Open device and disconnect the battery and input related battery adaptor to the battery socket, then connect phone battery to the battery adaptor.
2.Connect external power to iPower adaptor. (can be max 5V2A good quality charger, minimum 1A power. you can also use 4v from a good power supply). We have tested using 5v while unlocking iPhone 4s and iPhone 5. but if you have a bad quality charger that will supply more than 5v we recommend you to use an 4v external power.
3. Connect the light sensor to iPower adaptor white socket and put on the Phone (usually at a corner of the phone screen where no messages are displayed during boot procedure. Also avoid the middle of the screen as it will display the light increase icon and this can stop the unlocking prematurely).
4. Connect the USB 3 in 1 charging USB cable to iPower adaptor USB slot
5. Connect the USB 3 in 1 charging USB cable related connector to phone
6. Program the MFC with the appropriate code settings (Delay time is not relevant for this update as the timing is already automatic)
7. Insert MFC Dongle into the iPower Adaptor.
8. Insert micro usb cable charger to iPower adaptor(can be max 5V 2A good quality charger), Now the MFC LEDs will start blinking and the phone will power up automatically, Then connect MFC Dongle to 3 in 1 USB cable OTG port. Please do not connect MFC Dongle before any above steps as the unlocking process might not start correctly.
Once the code is found the phone will be automatically powered off and MFC Dongle stop sending codes. We had to do this to prevent phone going to permanently Disabled mode if the code found is not correct one. To be sure we got the right code you can unplug MFC Dongle from iPower adaptor (read the code using the computer if you wish) and plug back again into iPower adaptor to checking. If this time MFC Dongle stops again then you can be sure the code is the correct one. ATTENTION ! Do not move the light sensor from the previous position. Also it is recommend to use tape to tape the sensor to phone. Because phone vibrates after every code,the sensor position can change and the unlocking might get fail.
NOTE: USB 3 in 1 Charging/OTG cable is cable is sold separately
Additional information:
In case your phone displays Phone disabled 15 minutes remaining, you will have to wait at least 15 minutes before starting to unlock. Codes sent to the phone during this time will always be invalid even if the code is correct.
If phone displays 23 million minutes remaining it means the phone has lost correct time setting after taken out the battery. You can insert an active simcard into the phone to get the correct time and date then revert back to the normal 1,2,15,60 minutes waiting message etc. In our test we were able to use MFC even without simcard as the phone will revert back to the normal waiting time after the first reboot. But you need to take into consideration the fact that if the phone displays wait for 60 minutes then have to wait 60 minutes until you can really start to unlock procedure.
How to use:
1. Open device and disconnect the battery and input related battery adaptor to the battery socket, then connect phone battery to the battery adaptor.
2.Connect external power to iPower adaptor. (can be max 5V2A good quality charger, minimum 1A power. you can also use 4v from a good power supply). We have tested using 5v while unlocking iPhone 4s and iPhone 5. but if you have a bad quality charger that will supply more than 5v we recommend you to use an 4v external power.
3. Connect the light sensor to iPower adaptor white socket and put on the Phone (usually at a corner of the phone screen where no messages are displayed during boot procedure. Also avoid the middle of the screen as it will display the light increase icon and this can stop the unlocking prematurely).
4. Connect the USB 3 in 1 charging USB cable to iPower adaptor USB slot
5. Connect the USB 3 in 1 charging USB cable related connector to phone
6. Program the MFC with the appropriate code settings (Delay time is not relevant for this update as the timing is already automatic)
7. Insert MFC Dongle into the iPower Adaptor.
8. Insert micro usb cable charger to iPower adaptor(can be max 5V 2A good quality charger), Now the MFC LEDs will start blinking and the phone will power up automatically, Then connect MFC Dongle to 3 in 1 USB cable OTG port. Please do not connect MFC Dongle before any above steps as the unlocking process might not start correctly.
Once the code is found the phone will be automatically powered off and MFC Dongle stop sending codes. We had to do this to prevent phone going to permanently Disabled mode if the code found is not correct one. To be sure we got the right code you can unplug MFC Dongle from iPower adaptor (read the code using the computer if you wish) and plug back again into iPower adaptor to checking. If this time MFC Dongle stops again then you can be sure the code is the correct one. ATTENTION ! Do not move the light sensor from the previous position. Also it is recommend to use tape to tape the sensor to phone. Because phone vibrates after every code,the sensor position can change and the unlocking might get fail.
NOTE: USB 3 in 1 Charging/OTG cable is cable is sold separately
|
||
NEGOTIATE PRICE
Additional information about this product:
Information concerning features of this tool :Developer provides support only for those phones which are on the list of supported. Not all servicing features can be applied to some supported models, due to difference of hardware / software versions. Complete list of supported models you can find on the official product page, or on the GSM forum (GSMHosting).
Information concerning technical requiments :
The correct use of the purchased goods is required to have a stable internet connection with min . capacity of 1024 kb / s ( download) and 512 kb / s ( upload) . Before you attempt to make software update on the device or want to activate/use service, make sure that you have a sufficient link parameters .
Information concerning the interoperability of digital content:
For using a software or a piece of software that the manufacturer supplies with purchased hardware, in some cases it’s required that you disable your Firewall ( in software or router) and antivirus software. Leaving it enabled can occurs inproper operation of software / services and you will get communications errors like “Error 10060”.
Information concerning hardware requiments:
For proper working with this device producer suggest PC computer with 32-bit Windows XP operating system. We don't guarantee that software/device will work or any other system - especially 64-bit systems, iMac, Linux.
Information concerning IMEI change:
We want to inform that IMEI change option in softwares are intended to use only to repair broken IMEI and retrieve it to original state. It's prohibitted to use this function to change IMEI to diffrent that original. Multi-COM don't answer to any questions related with operation on IMEI number - if you require help in this metter please contact with software/device producer directly. We don't take any responsibility to use this function.
If you are interested in
iPower Adaptor for MFC Dongle
you will probably want to take a look at following products:
Dedicated equipments for this adapter:
+
|
MFC Dongle
more
|
Price:
299.00 EUR w/o VAT |
See also
+
|
Charging Cable 3in1 for MFC Dongle
more
|
Price:
29.00 EUR w/o VAT |
+
|
iP-Box iOS8 Adapter
more
|
Price:
55.00 EUR w/o VAT |
You might also be interested in:
|
+
|
MFC Dongle
more
|
Price:
299.00 EUR w/o VAT |
+
|
Easy-Box Dongle
more
|
Price:
30.00 EUR w/o VAT |
+
|
4SE SonyEricsson service USB key
more
|
Price:
70.00 EUR w/o VAT |
+
|
Pegasus Box
more
|
Price:
69.00 EUR w/o VAT |
+
|
Medusa Pro II Box - Full
more
|
Price:
789.00 EUR w/o VAT |
+
|
BlackBox (Bruteforce OPPO and VIVO)
more
|
Price:
115.00 EUR w/o VAT |
+
|
OctoPlus Pro Box Ultimate (LG+SAM+ SE/SONY + FRP+Huawei+JTAG/EMMC) 6in1
more
|
Price:
699.00 EUR w/o VAT |
+
|
Octoplus BOX with activation LG + SAMSUNG + FRP with 5in1 cables
more
|
Price:
270.00 EUR w/o VAT
0.00 EUR
|
This product was bought most often with:
|
+
|
MFC Dongle
more
|
Price:
299.00 EUR w/o VAT |
|
+
|
Charging Cable 3in1 for MFC Dongle
more
|
Price:
29.00 EUR w/o VAT |
|
+
|
iP-Box iOS8 Adapter
more
|
Price:
55.00 EUR w/o VAT |
+
|
Pattern Adapter for XPIN Clip
more
|
Price:
60.00 EUR w/o VAT |
+
|
XPIN Clip with cables set
more
|
Price:
349.00 EUR w/o VAT |
+
|
Universal adapter for JTAG Box
more
|
Price:
6.00 EUR w/o VAT |
+
|
Adapter EMMC ATF V2 4in1
more
|
Price:
25.00 EUR w/o VAT |
Note
1. Offered by us accessories and replacement parts are not original phone producer parts, but they have been carefully choosen from list of producers to offer highest quality.
2. Our company sale only hardware/HASP/Box - not software for it. Software can be found and downloaded directly from producers webpage.
3. All trademarks mentioned on this site are property of their respective companies. Including product names, logos, commercial symbols, trade names and slogans are trademarks of those respective or related companies, and are protected by international trademark laws, and they are used here only for information purpose.
