 |
We are sorry but product that you are looking is no longer available in our offer - there are available other similar products with similar functions:
For more information contact with us.
Tornado Infra Full station
Price:
499,00 EUR w/o VAT
Tornado Infra Full station it's first hand held infra rework station. Here is an honest attempt to give infra rework at reasonable price without any degradation in quality. Our product has been built using one of the best infrared techniques an best to use with lead-free PCB's.
Most common questions:
Q: What more can it do than a hot air?
A: First since 2006 June all PCB’s made all over the world must be lead free PCB’s. The melting temperature for lead free solder is 225 °C. Also if you have a PCB with lead free solder wire and if you try using hot air to repair it the PCB tracks can go bad. So there is no other choice but to use INFRA heating station
Q: How does this infra work?
A: The Infra rework consists of two units; one is the Pre Heater and the second one is a Hand Held unit. The Pre Heater is used as a base on which the PCB is placed and kept in place with the help of small magnetic foot. The Pre Heater is used to preheat the PCB up to a suitable temperature from the lower side. Approx mate temperature for preheat is 100 degrees which will display on the unit 300 in meter in the preheater. Once the PCB is preheated to the required temperature the Hand Held unit is used to heat the required part to a higher temperature (sufficient to melt the solder) and the required part can be removed. Another new part can be also be fixed in the same way – after proper application of flux
Specification:
Pre Heater:
This infrared heating element contains the CE marking.
The CE marking indicates conformity with the relevant European safety directive(s).
Heating element specifications:
Iron-chrome aluminum resistance wire
Heater Voltage: 230 Volts standard.
Electrical Power Loading: 6.8 W/cm2 (43.5W/inch)
Useful wavelength range: 2 to 10 Microns.
Average Operating Life: 5,000 - 10,000 Hours.
Mean Maximum Surface Temperature: 685°C
Approximate Time Until Top Temperature: 8 minutes
The heat up curves for ceramic heater are as shown below
Package contains:
- Infra Tornado station
- Preheater Tornado
- 2 power chord cables
- mulimter/termometr for measuring temp from Infra
- megnetic stops
- flux
We offer 6 months of warranty for this product
Most common questions:
Q: What more can it do than a hot air?
A: First since 2006 June all PCB’s made all over the world must be lead free PCB’s. The melting temperature for lead free solder is 225 °C. Also if you have a PCB with lead free solder wire and if you try using hot air to repair it the PCB tracks can go bad. So there is no other choice but to use INFRA heating station
Q: How does this infra work?
A: The Infra rework consists of two units; one is the Pre Heater and the second one is a Hand Held unit. The Pre Heater is used as a base on which the PCB is placed and kept in place with the help of small magnetic foot. The Pre Heater is used to preheat the PCB up to a suitable temperature from the lower side. Approx mate temperature for preheat is 100 degrees which will display on the unit 300 in meter in the preheater. Once the PCB is preheated to the required temperature the Hand Held unit is used to heat the required part to a higher temperature (sufficient to melt the solder) and the required part can be removed. Another new part can be also be fixed in the same way – after proper application of flux
Specification:
Pre Heater:
Heating element specifications:
The heat up curves for ceramic heater are as shown below
Package contains:
- Infra Tornado station
- Preheater Tornado
- 2 power chord cables
- mulimter/termometr for measuring temp from Infra
- megnetic stops
- flux
wARRANTY
We offer 6 months of warranty for this product
